AXESS AXDIS-TY3 Manual

Read below đź“– the manual in Italian for AXESS AXDIS-TY3 (24 pages) in the Not categorized category. This guide has been helpful for 20 people and has been rated 4.5 stars on average by 2 users

Page 1/24
AXDIS-TY3
INSTALLATION INSTRUCTIONS
AxxessInterfaces.com © COPYRIGHT 2024 METRA ELECTRONICS CORPORATION REV. 6/12/24 INSTAXDIS-TY3
INTERFACE FEATURES
TOOLS REQUIRED
Toyota Interface with SWC 2018-2021
APPLICATIONS
• Designed for both amplified and non-amplified models
• Provides accessory power (12-volt 10-amp)
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains the factory AUX-IN jack
• Retains the factory backup camera
• Includes an AXCSD-6V 12-to-6V step-down for the factory camera
• Retains audio controls on the steering wheel
• Retains balance on amplified models
(non-amplifed models retain balance and fade)
• Micro-B USB updatable
TOYOTA
4Runner ....................... 2020-Up
Avalon .......................... 2019-Up
C-HR ............................. 2019-Up
Camry........................... 2018-Up
Corolla .......................... 2019-Up
Highlander ................... 2020-Up
RAV4 ............................ 2019-Up
Sequoia ........................ 2020-Up
Sienna .......................... 2018-Up
Tacoma ........................ 2020-Up
Tundra ......................... 2020-2021
INTERFACE COMPONENTS
• AXDIS-TY3 interface • AXDIS-TY3 harness (LD-TYAMP3-SWC)
• Female 3.5mm connector with stripped leads
• AXCSD-6V
TABLE OF CONTENTS
Connections:
LD-TYAMP3-SWC ....................................................2
3.5mm Jack Steering Wheel Control Retention
... 3
Installing the AXDIS-TY3........................................3
Programming the AXDIS-TY3 ...............................4
Audio Level Adjustment .......................................4
Steering Wheel Control Settings ......................5-8
LED Feedback .......................................................5
Changing Radio Type ..........................................6
Remapping the SWC Buttons .............................7
Dual Assignment Instructions
.............................8
Troubleshooting.....................................................9
Product Info
Visit AxxessInterfaces.com for more detailed information
about the product and up-to-date vehicle specific applications.
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Small flat-blade screwdriver
• Tape
• Wire cutter
• Zip ties
ATTENTION: With the key out of the ignition, disconnect
the negative battery terminal before installing this product.
Ensure that all installation connections, especially the air
bag indicator lights, are plugged in before reconnecting the
battery or cycling the ignition to test this product.
NOTE: Refer also to the instructions included with the
aftermarket accessory before installing this device.
2
CONNECTIONS: LD-TYAMP3-SWC
Red - Accessory
Orange/White - Not Used
Blue/White - AMP turn on
Blue/Pink - Not Used
Light Green - Not Used
Green - Not Used
Green/Black - Not Used
Green/Purple - Not Used
Front
Rear
Sub
AUX-IN
Rear View
SWC
Aftermarket Radio
(Your radio’s features may vary)
Yellow - Battery wire
Black - Ground wire
Blue/Pink - VSS
Green/Purple - Reverse backup camera
LD-2NAVAMP
16-Pin
Purple - Not Used
Purple/Black - Not Used
Gray - Front Right Speaker +
Gray/Black - Front Right Speaker -
White - Front Left Speaker +
White/Black - Front Left Speaker -
Brown - Not Used
Purple/Black - Rear Right Speaker -
Purple - Rear Right Speaker +
Green/Black - Rear Left Speaker -
Green - Rear Left Speaker +
Black - Camera Ground
Red - Camera Power 6V
Light Green - E-Brake
Vehicle Connectors
LD-TYAMP3-SWC
22-Pin
AXCSD-6V
Blue/White - Reverse trigger
Black - Chassis ground
Blue/Red - 6V CAM PWR
Radio Connections
Vehicle Connector
3
REV. 6/12/24 INSTAXDIS-TY3
CONNECTIONS (CONT) INSTALLING THE AXDIS-TY3
3.5mm jack steering wheel control retention:
The 3.5mm jack is to be used to retain audio controls on the steering wheel.
• For the radios listed below: Connect the
female 3.5mm connector with stripped leads
, to the male
3.5mm SWC jack from the
AXDIS-TY3 harness
. Any remaining wires tape off and disregard.
• Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White
wire from the connector. Then connect the remaining steering wheel control wire, normally
Brown/White, to the Brown wire from the connector.
• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire.
• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to
the Brown wire.
Note: If the Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood.
See the instructions under changing radio type.
• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.
• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AXSWCH-PAR (sold
separately), then connect the 4-pin connector from the AXSWCH-PAR into the radio.
Note: The radio must be updated to rev. 2.1.4 or higher software.
• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A
or SWC-1, to the Brown wire from the connector. Then connect the remaining steering wheel
control wire, referred to as Key-B or SWC-2, to the Brown/White wire from the connector. If
the radio comes with a third wire for ground, disregard this wire.
Note: After the interface has been programmed to the vehicle, refer to the manual provided
with the radio for assigning the SWC buttons. Contact the radio manufacturer for more
information.
• For all other radios: Connect the 3.5mm jack from the
AXDIS-TY3 harness
into the jack from the
aftermarket radio designated for an external steering wheel control interface. Please refer to the
aftermarket radios manual if in doubt as to where the 3.5mm jack connects to.
With the key in the off position:
1.
Connect the 16-pin harness with stripped leads, and the AXDIS-TY3 harness into the
interface
.
2. Connect the
backup camera harness
to the wiring harness in the vehicle.
Attention!
Do not connect the AXDIS-TY3 harness to the wiring harness in the vehicle just yet.
Attention!
If retaining steering wheel controls, ensure that the jack/wire is connected to
the radio before proceeding. If this step is skipped, the interface will need to be reset for the
steering wheel controls to function.

Product Specifications

Brand: AXESS
Category: Not categorized
Model: AXDIS-TY3

Do you need help?

If you need help with AXESS AXDIS-TY3, ask a question below and other users will answer you




Not categorized AXESS User Manuals

AXESS

AXESS AXDSPX-BM1 Manual

25 October 2024
AXESS

AXESS AXDIS-BW122 Manual

13 October 2024
AXESS

AXESS 99-3303 Manual

13 October 2024
AXESS

AXESS AXBT-MZ2 Manual

13 October 2024
AXESS

AXESS AX-ALOC618 Manual

13 October 2024
AXESS

AXESS ANC-GMH3 Manual

13 October 2024
AXESS

AXESS ANC-GMH2 Manual

13 October 2024
AXESS

AXESS ANC-CHH2 Manual

13 October 2024
AXESS

AXESS AX-AB-CH3 Manual

13 October 2024
AXESS

AXESS AX-AB-CH4 Manual

13 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals