Extron TLP Pro 525C Manual
Read below š the manual in Italian for Extron TLP Pro 525C (10 pages) in the Monitor category. This guide has been helpful for 17 people and has been rated 4.5 stars on average by 2 users
Page 1/10
1
TLP Pro 525C Series ā¢ Setup Guide
Overview
The Extron TLP Pro 525C is a 5-inch Cable Cubby touchpanel. It has a īip-up, 800x480 (WVGA), LCD touchscreen with
24-bit color depth. The TLP Pro 525C NC is a streamlined model, with a set of features that adhere to government and military
security protocols.
These touchpanels are suitable for any AV application requiring a Cable Cubby touchpanel with a customizable interface.
This guide provides instructions for experienced installers to mount and install these touchpanels. For more complete instructions,
see the TLPīPro 525C and 725C Series User Guide at www.extron.com.
Setup Checklist
Get Ready
ī
Download and install the latest version of the following software:
ī
GUI Designer ā For designing layouts for Extron TouchLink
Ā®
Pro touchpanels and third party touch interfaces.
ī
Global Configurator
Ā®
Professional and Global Configurator Plus ā For setting up and conīguring the control
processor and touchpanel.
ī
Toolbelt ā Provides device discovery, device information, īrmware updates, and conīguration of network settings,
system utilities, and user management for TouchLink Pro devices.
ī
Global Scripter
Ā®
ā Provides an integrated development environment for Extron control systems programming.
NOTE: All four software programs are available from www.extron.com.
ī
Obtain the following network information from your network administrator:
ī
DHCP status ā (on or off). If DHCP is off, you must also obtain:
ī
IP address ī
Subnet mask ī
Gateway
ī
User name ā This can be either admin or user.
ī
Password ā The factory conīgured passwords for all accounts on this device have been set to the device serial
number. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password will be the default password conīguration. The default
password is extron (for either admin or user).
ī
Make a note of the touchpanel MAC address.
ī
Make sure you are familiar with all the included parts and have all the necessary Tools Required for Installation (see
page 4) for installing the cable cubby.
Included Parts
Check that all the following parts are included:
3/8ā Hole Plug (4)1/4ā Hole Plug (1)
#6-32 Screw (4)#6 Star Washer (4)
TLP Pro 525C or
TLP Pro 525C NC (1)
2-space
MAAP Frame (1)
TLP Pro 525C
Connectivity
Bracket (1)
Short Clevis Pin (1)
Cotter Pin (1)
HDMI Lockit (1)
Tie wrap (1)
5-cable Pass-through
Plate (1)
Figure 1. TLP Pro 525C Included Parts
NOTE: Active or passive MAAPs must be purchased separately (see www.extron.com).
2
TLP Pro 525C Series ā¢ Setup Guide (Continued)
Mount and Cable All Devices
ATTENTION:
ā¢ Do not power on the touchpanels until you have read the attention notiīcation in the āBase Featuresā section of the
TLPīPro 525C and 725C Series User Guide.
ā¢ Ne branchez pas les Ć©crans tactiles avant dāavoir lu la mise en garde de la section Ā«īBase Features Ā» du TLPīPro 525C and
725C Series User Guide.
ī
Cut a hole in the table (see Step 1 ā Verify Cut-out Dimensions on page 4 and Step 2 ā Cut the Surface on
page 5).
ī
Run cables to the cable cubby (see Step 3 ā Run all Cables on page 5).
ī
Install modules into the Cable Cubby enclosure. Multiple optional modules can be installed in the TLP Pro 525C Cable Cubby
in a variety of conīgurations. Decide which modules and which conīguration best serve your needs. Options include:
ā¢ Cable Retractors (see Step 4 ā Install Cable Retractors (Optional) on page 5).
ā¢ Pass-through Cable Modules (see Step 5 ā Assemble the Pass-through Cable Module (Optional) on page 6).
ā¢ AAP Modules (see Step 6 ā Assemble the MAAP Module (Optional) on page 6).
ā¢ Power Modules (see Step 7 ā Install Modules on page 7).
ī
Use the setup menu for initial conīguration of the touchpanel (see Setup Menu on page 10).
ī
Mount the units (see Step 8 ā Mounting the Enclosure on page 9).
ī
Connect the touchpanel to a Power over Ethernet (PoE) injector (see ļ¬gure 13 on page 10).
ī
Connect the power injector to the LAN and power it on (see ļ¬gure 13).
Set up the Touchpanels for Network Communication
ī
Connect the PC that you are using for setup, the control processor, and the touchpanel to the same Ethernet subnetwork.
ī
Use the Setup Menu (see page 10) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,
gateway, and related settings for the touchpanel.
Conļ¬gure the Touchpanels
The GUI Designer Help File, the Global Conļ¬gurator Help File, and the Toolbelt Help File provide step-by-step instructions and
detailed information. The Global Conļ¬gurator Help File includes an introduction to the software and sections on how to start a
project and conīguration.
Global Scripter provides an Extron-exclusive Python library (ControlScript
Ā®
) and Global Scripter modules to get you started.
3
Front Panel Features
A
LCD screen ā The TLP Pro 525C series has a 5-inch
touchscreen with a 800x480 resolution.
B
Motion sensor ā Detects motion between three to īve
feet from the touchpanel, and at least 15Ā° from the center
axis.
ā¢ When no motion has been detected for a user-
deīned period of time, the touchpanel enters sleep
mode.
ā¢ When motion is detected by the sensor, the screen
display is restored and active.
C
Communication LED ā This LED shows the
conīguration and connection status of the touchpanel:
ā¢ Unlit during normal operation (the touchpanel is
conīgured and connected to an IP Link Pro control
processor).
ā¢ Blinks red if the touchpanel has been conīgured but
is not connected to an IP Link Pro control processor.
ā¢ Permanently lit if the touchpanel has not been
conīgured and is not connected to an IP Link Pro
control processor.
The indicator can be toggled between enabled and
disabled, using the Setup Menu (see page 10).
D
Light sensor ā This sensor monitors ambient light level
and adjusts screen brightness, based on the settings
conīgured using the Setup Menu.
īgure 2
A
A
A
B
B
B
C
C
C
D
D
D
B
B
B
F
F
F
E
E
E
Figure 2. TLP Pro 525C Front Panel and Enclosure
Features
Enclosure Features
E
Activation switch ā The left side of the lid hinge mechanism contains a switch. When the lid is closed, the switch sends the
screen into sleep mode. When the lid is opened, the screen display is restored and active.
When the lid is shut, the screen is not activated by motion near the touchpanel.
F
Speaker ā A single speaker, located on the side of the enclosure, provides audible feedback for the user.
Base Panel Features
These features are accessed from underneath the touchpanel.
A
Menu button ā Pressing the Menu button activates the setup
menu (see Setup Menu).
B
Reset button ā Pressing the Reset button allows the unit to be
reset in any of three different modes (for an overview, see Reset
Modes: a Brief Summary on page 10).
C
Reset LED ā Provides feedback about the reset status when
the user presses the Reset button (see Reset Modes: a Brief
Summary).
D
USB port ā Compatible with USB 2.0.
E
LAN/PoE port ā The TLP Pro 525C must be powered
through this port (see Step 9 ā Connecting the Power to the
Touchpanel on page 10 for details).
īgure 3
MENU
RESET
USB
275 mA
LAN / PoE
D
D
DE
E
EA
A
AB
B
BC
C
C
Figure 3. TLP Pro 525C Base Panel
ATTENTION:
ā¢ Do not power on the touchpanel until you have read the attention notiīcation in the āBase Featuresā section of the TLPīPro
525C and 725C Series User Guide.
ā¢ Ne branchez pas les Ć©crans tactiles avant dāavoir lu la mise en garde de la section Ā«īBase Features Ā» du TLPīPro 525C and
725C Series User Guide.
NOTE: Once the enclosure is permanently mounted, the Menu and Reset buttons are under the table and may be difīcult to
access. Use the setup menu to conīgure the TLP Pro 525C before mounting the unit.
Product Specifications
| Brand: | Extron |
| Category: | Monitor |
| Model: | TLP Pro 525C |
Do you need help?
If you need help with Extron TLP Pro 525C, ask a question below and other users will answer you
Monitor Extron User Manuals
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
Monitor User Manuals
- Monitor Sony
- Monitor Samsung
- Monitor LG
- Monitor Bosch
- Monitor Huawei
- Monitor HP
- Monitor Philips
- Monitor Panasonic
- Monitor Vorago
- Monitor Jensen
- Monitor Gigabyte
- Monitor AOC
- Monitor Hisense
- Monitor TCL
- Monitor Godox
- Monitor Kogan
- Monitor Behringer
- Monitor Planar
- Monitor Asus
- Monitor Lenovo
- Monitor JVC
- Monitor EMOS
- Monitor Optoma
- Monitor Yealink
- Monitor Dell
- Monitor Brandson
- Monitor Mybeo
- Monitor CSL
- Monitor Bearware
- Monitor Viewsonic
- Monitor Nec
- Monitor Ag Neovo
- Monitor Dahua Technology
- Monitor Simrad
- Monitor Posiflex
- Monitor Hikvision
- Monitor Acer
- Monitor Joy-it
- Monitor Iiyama
- Monitor Sharp
- Monitor Titan Army
- Monitor Soundstream
- Monitor MSI
- Monitor Chauvet
- Monitor Cocopar
- Monitor Asrock
- Monitor Advantech
- Monitor Orion
- Monitor BenQ
- Monitor Antelope Audio
- Monitor DTEN
- Monitor Bauhn
- Monitor Crestron
- Monitor IOIO
- Monitor Barco
- Monitor GVision
- Monitor Postium
- Monitor OSEE
- Monitor Ikan
- Monitor Approx
- Monitor Triton
- Monitor Voxicon
- Monitor KRK
- Monitor Vimar
- Monitor HoverCam
- Monitor HyperX
- Monitor ELO
- Monitor Mobile Pixels
- Monitor Ernitec
- Monitor TVLogic
- Monitor Enttec
- Monitor Feelworld
- Monitor Elvid
- Monitor Freedom Scientific
- Monitor UPERFECT
- Monitor Qian
- Monitor IStarUSA
Latest Monitor User Manuals
27 October 2024
27 October 2024
27 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024