Blaupunkt THA500.1 Manual

Read below 📖 the manual in Italian for Blaupunkt THA500.1 (8 pages) in the Not categorized category. This guide has been helpful for 33 people and has been rated 4.5 stars on average by 2 users

Page 1/8
THA500.1
1 062 310 500 001
Warranty
We provide manufacturer's warranty for 12 months
from the date of sale for Blaupunkt products purchased
within India.
Recommendation
The performance of an ampliî›¶er can only be as good as
its installation. Correct installation increases the overall
performance of your car sound system. The THA
ampliî›¶er should be installed by a trained person. If you
installation instructions very carefully and allow yourself
sufficient time for the installation.
health protection:
During playback of music in your vehicle, please
100 dB can lead to permanent damage of the human ear
& in some cases loss of hearing. Using today's high-
performance systems and loudspeaker conî›¶gurations
allows for reaching sound-pressure levels above 130 dB.
Safety notes
Please observe the following safety notes during the
installation and connection.
Observe safety notes of the vehicle manufacturer.
- When you drill holes, ensure that you do not damage
any vehicle components.
- Please use minimum 10AWG power & ground cable
with a fuse located within 18 inches of the battery.
- Use cable glands for holes with sharp edges.
- Incorrect installation can result in malfunction of
vehicle electronic systems or sound system.
Installation and connection instructions
With respect to accident safety, the THA 500.1 must be
secured fastened at its mounting location.
When selecting the installation location, select a dry
the ampliî›¶er.
seats or other locations that are open to the passenger
cabin.
The installation location must be suitable to accept the
accompanying screws and provide a î›¶rm support.
battery in case of a short circuit between power
only the ampliî›¶er, not the vehicle battery.
Use loudspeakers with 2 - 4 Ohms impedance (see table
or installation drawing). Do not connect loudspeakers to
ground, use only the referenced terminals.
Audio inputs (see Fig. 3)
You can select between 2 different audio inputs;
- Cinch (RCA)
- Hi level (loudspeaker connections)
Use only one of the audio inputs; otherwise, it may lead
to audio interference.
The preampliî›¶er outputs are connected to the cinch
(RCA) sockets ) via a shielded sound cable. j
connections of pos. / are fed to the closest k l
be observed. Bridge output stages (BTL) can also be
connected directly without an additional adapter.
Positive / negative connection
- We recommend a minimum cross section of 10 AWG
- Route commercially available positive cable to the
battery and connect via fuse holder.
- Use cable glands for holes with sharp edges.
- Securely fasten commercially available negative
cables to a noise-free ground point (chassis screw,
chassis metal) not to the negative pole of the battery.
they are bright and grease with graphite grease.
Integrated fuses (Fuse)
The fuses integrated in the ampliî›¶er (Fuse) protect the
power ampliî›¶er and the entire electrical system in case
of an error. If a replacement fuse is used, never bridge
fuses or replace them with a type with higher current.
1 x 500 W / 2
25 Hz - 500 Hz
> 100 dB @ RMS power
> 75 dB @ 1W/1kHz
<0.15%
0.2 / 5V
50 - 500Hz
185 x 54 x 184
7.3 x 2.1 x 7.3
0 dB / 6 dB
THA500.1 THA500.1
RMS power
THA500.1 THA500.1
frequency crossovers
settings shown are required (Fig. 3). The frequency is
de pen den t up on the fr equency ra nge o f th e
loudspeakers (see recommended frequency range of
the loudspeakers).
Low-pass frequency control
This control is active if the switch is in the position "Low-
Pass", and allows for setting the desired entry frequency.
frequenc y range of 50Hz to 5 00Hz . (Ideal for
Subwoofers).
Bass boost
The bass boost control is used to adjust the bass
response of the ampliî›¶er.
The setting options are: 0 dB / +6 dB.
Power-on indicator (PWR / PRO)
Green LED: Output stage on, regular operating status.
Red LED: Output stage is electronically switched off due
to an error.
Recycling & Disposal
Please use the return and collection systems
available to dispose of the product.
Subject to changes
Connection examples
Connection of the voltage supply............Fig. 2
Audio inputs....................................................Fig. 3
Loudspeaker connections..........................Fig. 4/5
Remote connection of the ampliî›¶er with switchable
+12V voltage source.
the on/off-switch of the radio device.
Level control
The Level control is used to adjust the input sensitivity of
the power ampliî›¶er to the output voltage of your car
sound system preampliî›¶er output.
The adjustment range is from 0.2 V to 5V.
If a car sound system of a third party manufacturer is
connected, the input sensitivity must be adjusted
corresponding to the manufacturer data.
An important explanation in this context:
However, this is not a volume control; no further
ampliî›¶er output can be achieved in the full position,
even if it may sound like that at the beginning. The
system merely increases the volume faster if the volume
control of the car sound system is turned up.
DC Offset- 4
When connecting to an OE radio, it may not be possible
to connect the remote turn on lead on the ampliî›¶er,
please use the high level input available on the side
panel & turn on DC Offset to automatically turn on/off
the amplier when the OE radio is turned on / off.
Loudspeaker connections
As with every audio component, the correct polarity of
ampliî›¶er and loudspeakers is important for a good bass
response. For this reason, ensure that the positive (+)
connection of the ampliî›¶er is connected with the
positive connection (+) of the loudspeaker; the same
applies to the negative (-) connections. In addition, the
left ampliî›¶er channel must be connected with the left
right loudspeaker.
Caution:
Ampliî›¶er load must not be lower than 2 Ohms. A
lower load leads to overheating & cause the
amplier to switch off & can cause permanent
damage.

Product Specifications

Brand: Blaupunkt
Category: Not categorized
Model: THA500.1

Do you need help?

If you need help with Blaupunkt THA500.1, ask a question below and other users will answer you




Not categorized Blaupunkt User Manuals

Blaupunkt

Blaupunkt BP-JR20 Manual

26 October 2024
Blaupunkt

Blaupunkt MPT 25 Manual

15 October 2024
Blaupunkt

Blaupunkt BP-GT01 Manual

14 October 2024
Blaupunkt

Blaupunkt BP-FT01 Manual

14 October 2024
Blaupunkt

Blaupunkt THA 285 Manual

14 October 2024
Blaupunkt

Blaupunkt THA500.1 Manual

14 October 2024
Blaupunkt

Blaupunkt BP-YF06 Manual

14 October 2024
Blaupunkt

Blaupunkt BP-PJ02 Manual

14 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals