Broan 198 Manual
Read below 📖 the manual in Italian for Broan 198 (2 pages) in the Heater category. This guide has been helpful for 27 people and has been rated 4.5 stars on average by 2 users
Page 1/2
MODELS 192 • 194 • 198
Page 1
Wall Heater
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE
INSTALLING OR USING THIS HEATER.
To reduce the risk of fire, electric shock, or injury
to persons, observe the following:
1. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch
power off at service panel and lock the service
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be
locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring
must be done by a qualified person(s) in
accordance with all applicable codes and
standards, including fire-rated construction
codes and standards.
4. When cutting or drilling into wall or ceiling,
do not damage electrical wiring and other
hidden utilities.
5. This heater is hot when in use. To avoid burns,
do not let bare skin touch hot surfaces. Keep
combustible materials, such as furniture,
pillows, bedding, papers, clothes, etc. and
curtains at least 3 feet (0.9 m) from the front
of the heater.
6. Extreme caution is necessary when any
heater is used by or near children or invalids
and whenever the heater is left operating
and unattended.
7. Do not operate any heater after it
malfunctions. Disconnect power at service
panel and have heater inspected by a
reputable electrician before reusing.
8. Do not use outdoors.
9. To disconnect heater, turn controls to
off, and turn off power to heater circuit at
main disconnect panel (or operate internal
disconnect switch, if provided).
10. Do not insert or allow foreign objects to
enter any ventilation or exhaust opening, as
this may cause an electric shock or fire, or
damage the heater.
11. To prevent a possible fire, do not block air
intakes or exhaust in any manner.
12. A heater has hot and arcing or sparking
parts inside. Do not use it in areas where
gasoline, paint, or flammable vapors or
liquids are used or stored.
13. Use this heater only as described in this
manual. Any other use not recommended
by the manufacturer may cause fire, electric
shock, or injury to persons.
14. Install heater at least 12 inches from floor or
any adjacent wall.
15. To avoid electrical shock: Do not install
unit in a tub or shower enclosure or any
location where it may come in contact with
water. Never place a switch where it can be
reached from a tub or shower.
16. This product may ONLY be installed vertically
in a wall. Do not mount in any other position.
17. Do not connect heater to dimmer switch or
speed control.
18. This product must be grounded.
SAVE THESE INSTRUCTIONS
MODELS 192 • 194 • 198
Page 2
PLANNING
This heater is intended to be used to supply
supplemental heat from a wall location in new or
existing construction.
Choose a location where edge of heater will be
at least 12” from the floor or any adjacent vertical
surface.
The heater can be operated using its built-in ther-
mostat or a remote thermostat (such as the Model
86W Line-Voltage thermostat or an appropriate
low-voltage thermostat and transformer/relay). The
Model 85 Kit is available for surface-mount appli-
cations. Purchase these accessories separately.
Plan to supply the heater with proper line voltage
and appropriate power cable.
NOTE: Power can be tapped from a nearby circuit
depending on the heater wattage required and the
amperage rating of the circuit.
Heater can be converted to half-wattage to avoid
overloading such circuits.
MODEL VOLTS AMPS WATTS BTU/HR
192 240 8.33/4.17 2000/1000 6827/3413
194 240 12.50/6.25 3000/1500 10240/5120
198 240 16.67/8.33 4000/2000 13653/6827
Bold ratings are factory wired.
See “OPTIONAL WIRING CONVERSIONS” sec-
tion for wattage conversion instructions.
Follow these basic steps when installing this heater:
1) Nail housing to studs.
2) Connect power cable.
3) Fasten heater assembly and grille to housing.
DRYWALL
THERMAL
OVERLOAD
GRILLE
BUILT-IN
THERMOSTAT
HEATER HOUSING
POWER CABLE
Product Specifications
| Brand: | Broan |
| Category: | Heater |
| Model: | 198 |
Do you need help?
If you need help with Broan 198, ask a question below and other users will answer you
Heater Broan User Manuals
26 October 2024
26 October 2024
14 October 2024
Heater User Manuals
- Heater Candy
- Heater Delonghi
- Heater Domo
- Heater Cecotec
- Heater Noveen
- Heater Kogan
- Heater SereneLife
- Heater Olimpia Splendid
- Heater Sencor
- Heater Orava
- Heater Hortus
- Heater EMOS
- Heater Fluval
- Heater Gude
- Heater Ryobi
- Heater Bimar
- Heater Velleman
- Heater Livoo
- Heater Brandson
- Heater Ausclimate
- Heater Ufesa
- Heater Bromic
- Heater Omega Altise
- Heater Adler
- Heater Master
- Heater Einhell
- Heater Eden
- Heater Tristar
- Heater Guardian
- Heater Eldom
- Heater Brentwood
- Heater Chauvet
- Heater Korona
- Heater Stanley
- Heater Big Ass Fans
- Heater Bionaire
- Heater Herschel
- Heater AustWood
- Heater Eurolite
- Heater Kenmore
- Heater Mellerware
- Heater Otsein-Hoover
- Heater Perfect Aire
- Heater LifeSmart
- Heater EvoHeat
- Heater Eurom
- Heater NewAir
- Heater Optimum
- Heater MSW
- Heater Uniprodo
- Heater Yellow Garden Line
- Heater Ravanson
- Heater Sonnenkonig
- Heater United
- Heater Enders
- Heater Mission Air
- Heater Kemlan
- Heater Duro Pro
- Heater Yamazen
- Heater Mestic
- Heater SHX
Latest Heater User Manuals
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
26 October 2024
26 October 2024
25 October 2024