Eller ELBC005TK Manual

Read below 📖 the manual in Italian for Eller ELBC005TK (4 pages) in the Not categorized category. This guide has been helpful for 12 people and has been rated 4.5 stars on average by 2 users

Page 1/4
Louis Reyners B.V.
Handleiding voor bediening en veiligheidsinstructies voor de ELLER
tentklem – ELBC005TK
Lees deze instructies zorgvuldig door en bewaar ze. Lees ze aandachtig voordat u probeert het
beschreven product te monteren, installeren, bedienen of onderhouden. Bescherm uzelf en anderen
door alle veiligheidsinformatie in acht te nemen. Het niet naleven van instructies kan persoonlijk letsel
en/of eigendomsschade veroorzaken! Bewaar de instructies voor toekomstige referentie.
Beschrijving
De ELLER tentklemmen (ELBC005TK) zijn ontworpen om een veilige, semi-permanente ophang- of
bevestigingspunt te bieden in een tentprofiel met een buitenbreedte van minimaal 60 mm en maximaal
105 mm.
Algemene veiligheidsinformatie
Deze handleiding bevat belangrijke informatie voor de juiste installatie, bediening en onderhoud van de
hierin beschreven klem. Alle personen die betrokken zijn bij dergelijke installatie, bediening en
onderhoud moeten volledig vertrouwd zijn met de inhoud van deze handleiding. Volg de aanbevelingen
en instructies van deze handleiding op en bewaar deze voor verdere referentie om te voorkomen dat
eigendomsschade of persoonlijk letsel optreedt. De apparatuur die in deze handleiding wordt getoond,
is uitsluitend bedoeld voor industrieel gebruik en mag niet worden gebruikt om personen te tillen, te
ondersteunen of anderszins te vervoeren.
WAARSCHUWING
Om schade en/of persoonlijk letsel te voorkomen:
a. Overschrijd de maximale werklast (WLL) niet.
b. Gebruik de klem niet om mensen of materialen te tillen.
c. Gebruik de klem niet op flensbreedtes buiten het aangegeven bereik.
d. Smeer het schroefdraad van de klem regelmatig in.
e. Controleer de klem vóór elk gebruik en periodiek op gebarsten, versleten of vervormde onderdelen.
f. Volg de instructies voor het hijsmateriaal dat met de klem wordt gebruikt.
g. Zorg ervoor dat de klem voldoende is aangedraaid voordat u deze gebruikt.
h. Gebruik niet in geval van visuele vervorming.
i. Deze klem moet minstens 1 keer per jaar worden getest op 125% van de maximale werklast door een
erkende keurinstantie. De bijbehorende documenten moeten traceerbaar zijn en altijd beschikbaar
zijn voor de gebruiker.
j. Bedrijfstemperatuur moet tussen de -10 / +50 graden Celsius zijn.
k. Het is verboden om enige aanpassingen te doen aan de klem.
Installatie en bediening
Controleer of de breedte van het tentprofiel overeenkomt met de specificaties van de flensbreedte van
de klem. De tentklem wordt geopend door de schroefdraadstang te draaien totdat de klem op het
profiel kan worden geplaatst. De klem wordt vervolgens gesloten door de rotatie van de stang om te
keren. Zorg ervoor dat de klem correct wordt gepositioneerd met klauw aan de binnenkant van de keder
en dat de schroefdraadstang voldoende is aangedraaid zodat het gekartelde deel van klauw contact
maakt met de binnenkant van de keder. Zodra de klem stevig aan het profiel is bevestigd, breng dan de
belasting aan op het midden van de ophangstang van de klem. De klem kan worden gebruikt met een
maximale hoek van 30 graden. Til de belasting een korte afstand op of span de belasting aan om ervoor
te zorgen dat er een rechte lijnspanning op de klem wordt toegepast en dat er geen overmatige buiging
plaatsvindt in het tentprofiel.
Louis Reyners B.V.
Operating Instructions Manual and Safety Instructions for the ELLER
tent clamp – ELBC005TK
Please read and save these instructions. Read carefully before attempting to assemble, install, operate
or maintain the product described. Protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and / or property damage! Retain
instructions for future reference.
Description
The ELLER tent clamps (ELBC005TK) are designed to provide a secure semi-permanent suspension or
rigging point in a tent profile with an outside width of minimum 60 mm and a maximum of 105 mm.
General Safety information
This manual contains important information for the correct installation, operation, and maintenance of
the equipment described herein. All persons involved in such installation, operation and maintenance
should be thoroughly familiar with the contents of this manual. To safeguard against the possibility of
property damage or personal injury follow the recommendation and instructions of this manual and
keep it for further reference. The equipment shown in this manual is intended for industrial use only
and should not be used to lift, support, or otherwise transport people.
WARNING
To avoid damage and / or personal injury:
a. Do not exceed the Working Load Limit (WLL) of the clamp.
b. Do not use clamp to lift people or materials.
c. Do not use clamp on flange widths outside the rated range.
d. Do lubricate the clamp thread regularly.
e. Do check the clamp prior to every use and periodically for cracked, worn or deformed parts.
f. Do follow the instructions for the lifting equipment used with the clamp.
g. Make sure the clamp is tightened enough before use.
h. Do not use in case of visual deformation.
i. This clamp need to be tested at least 1 x every year at 125% of WLL by a recognized inspection
company. The corresponding documents need to be traceable and available by the user at al times.
j. Operating temperature -10 / +50 degrees Celsius.
k. It is forbidden to modify the clamp.
Installation and operation
Verify that the tent profile width matches the clamp flange width specifications. The tent clamp is
opened by rotating the threaded bar until the clamp can be positioned on the profile. The clamp is then
closed by reversing the rotation of the bar. Make sure that the clamp is being positioned correctly with
the suspension bars hanging on the inside of the keder and that the threaded bar is tightened enough
that the knurled part of the suspension bar is contacting the inside of the keder. Once the clamp is
securely attached to the profile, apply the load to the centre of the clamp suspension bar. The clamp can
be used with a maximum angle of 30 degrees. Lift the load a short distance or tension the load to ensure
that straight line pull is applied to the clamp and that the tent profile deflection is not excessive.
Louis Reyners B.V.
Picture of correct usage
0° & <5° = WLL 500 kg >5° & <30° = WLL 250 kg
Part list

Product Specifications

Brand: Eller
Category: Not categorized
Model: ELBC005TK

Do you need help?

If you need help with Eller ELBC005TK, ask a question below and other users will answer you




Not categorized Eller User Manuals

Eller

Eller ELBC005TK Manual

15 October 2024
Eller

Eller ELBCH Manual

15 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals