Ernitec 0070-08117 Manual
Ernitec
Security camera
0070-08117
Read below 📖 the manual in Italian for Ernitec 0070-08117 (4 pages) in the Security camera category. This guide has been helpful for 20 people and has been rated 4.5 stars on average by 2 users
Page 1/4
Special Announcement
For more information, please refer to website.
Fully understand this document before using this device, and
strictly observe rules in this document when using this device. If
you install this device in public places, provide the tip "You have
entered the area of electronic surveillance" in an eye-catching
place. Failure to correctly use electrical products may cause fire
and severe injuries.
It alerts you to moderate dangers which, if not
avoided, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may
cause device damage, data loss, device
performance deterioration, or unpredictable results.
It provides additional information.
Ÿ Strictly observe installation requirements when installing the
device. The manufacturer shall not be held responsible for
device damage caused by users' non-conformance to these
requirements.
Ÿ Strictly conform to local electrical safety standards and use
power adapters that are marked with the LPS standard when
installing and using this device. Otherwise, this device may be
damaged.
Ÿ Use accessories delivered with this device. The voltage must
meet input voltage requirements for this device.
Ÿ If this device is installed in places with unsteady voltage, ground
this device to discharge high energy such as electrical surges in
order to prevent the power supply from burning out.
Ÿ When this device is in use, ensure that no water or any liquid
flows into the device. If water or liquid unexpectedly flows into
the device, immediately power off the device and disconnect all
cables (such as power cables and network cables) from this
device.
Ÿ Do not focus strong light (such as lighted bulbs or sunlight) on
Ÿ Avoid heavy loads, intensive shakes, and soaking to prevent
damages during transportation and storage. The warranty does
not cover any device damage that is caused during secondary
packaging and transportation after the original packaging is
taken apart.
Ÿ Protect this device from fall-down and intensive strikes, keep
the device away from magnetic field interference, and do not
install the device in places with shaking surfaces or under
shocks.
Ÿ Clean the device with a soft dry cloth. For stubborn dirt, dip the
cloth into slight neutral cleanser, gently wipe the dirt with the
cloth, and then dry the device.
Ÿ Do not jam the ventilation opening. Follow the installation
instructions provided in this document when installing the
device.
Ÿ Keep the device away from heat sources such as radiators,
electric heaters, or other heat equipment.
Ÿ Keep the device away from moist, dusty, extremely hot or cold
places, or places with strong electric radiation.
Ÿ If the device is installed outdoors, take insect- and moisture-
proof measures to avoid circuit board corrosion that can affect
monitoring.
Ÿ Remove the power plug if the device is idle for a long time.
Ÿ All complete products sold by the manufacturer are delivered
along with nameplates, quick setup guide and accessories after
strict inspection. The manufacturer shall not be held
responsible for counterfeit products.
Ÿ The manufacturer will update this manual according to product
function enhancement or changes and regularly update the
software and hardware described in this manual. Update
information will be added to new versions of this manual without
prior notice.
Ÿ This manual may contain misprints, technology information that
is not accurate enough, or product function and operation
description that is slightly inconsistent with the actual product,
the final interpretation of company is as a standard.
Ÿ This manual is only for reference and does not ensure that the
information is totally consistent with the actual product. For
consistency, see the actual product.
Precautions
Open the package, check the appearance of product for no
obvious damage, and confirm the item list for table 1-1 is
consistent.
Table 1-1 Packing list
2.1 Device Ports
Component
Quantity
Remark
Vandal Dome Network Camera
Plastic anchor
Stainless self-tapping screw
Installation location sticker
Quick Setup Guide
1
3
3
1
1
NOTE
NOTE
this device. Otherwise, the service life of the image sensor may
be shortened.
Ÿ If this device is installed in places where thunder and lightning
frequently occur, ground the device nearby to discharge high
energy such as thunder strikes in order to prevent device
damage.
L hexagonal wrench
1
CAUTION
WARNING
WARNING
CAUTION
1
Open Package Examination
1
Device Structure
2
Figure 2-1 Device ports
2.2 Camera Dimensions
Figure 2-2 Dimensions of Dome(Unit:mm）
Different devices may have different dimensions; Please
refer to the actual product.
NOTE
Auxiliary thread-line tool
Reset
button
Long press the button for 5 seconds to
restore the original settings.
Alarm/
Audio
Alarm
out/in
out A, alarm out A
Applied
for alarm
function
out B, alarm out B
G, ground
In, alarm in
Audio
out/in
In, audio in
Applied
for audio
function
Out, audio out
G, ground
Analog
video
CVBS, analog video output
G, ground
Network
access port
Connects to a standard Ethernet cable.
12V power
supply
The ports are 12V/ OUT/12V/IN.
Uses the to auxiliary thread-line tool
through the cable
There are two rubber stoppers, user
can use the tool (screw driver or L
hexagonal wrench )to pierce the stopper,
and plug all cords in.
Remark
Over cable
rubber
stopper
Table 2-1 Interface of camera
Port name
Description
φ140
57.5
109.5
100°
φ110
123°
Over
function-
cord rubber
stopper
NOTE
Different devices may have different device ports; Please
refer to the actual product.
Green terminal block 3.81-9P
Green terminal block 3.81-4P
1
1
Reset
Alarm/Audio
interface
Over-line
buckle
Network access
port
Over -line
buckle
12V power supply
interface
Over function-cord
rubber stopper
Over cable rubber
stopper
Vandal Dome Network Camera
Quick Setup Guide
Item no.: 0070-08117
Precautions
Step 5 The set screw should be aligned the direction icon of base
panel, then rotate the device clockwise to the extreme
position, then tighten the set screw to lock block.
Figure 3-4 Install device
Figure 3-6 Assembling cover
4.3 Browsing Video
To ensure the real-time video can be played properly, you must perform
the following operation when you login the web for the first time:
If you can view the live video directly, please ignore the steps of adding
trusted sites.
Figure 4-3 Adding a trusted site
Step 2 In the Internet Explorer, choose Tool > Internet Options >
Security > Customer level, and set Download unsigned
ActiveX control and initialize and script ActiveX controls not
marked as safe for scripting under ActiveX controls and
plug-ins to Enable, as shown in figure 4-4.
Step 3 Download and install the player control as prompted.
If the repair tips are displayed when installing the control , please
ignore the prompt, and continue the installation, close the browser
during installing. Then login the page again.
Step 1 The Internet Explorer. Choose Tools > Internet options >
Security > Trusted sites > Sites, in the display dialog box, click
Add, as shown in figure 4-3.
To browse a real-time video, login the device and click Live
Video. The Live Video page is displayed, as shown in figure 4-5.
Figure 4-5 Live Video
Figure 4-4 Configuring ActiveX control and plug-in
NOTE
4.1 Login
Step 1 Open the Internet Explorer, input the IP address of IP camera
(the default value: 192.168.0.120) in the address box, and press
Enter. The login page is displayed as shown in figure 4-1.
Step 2 Input the user name and password.
Ÿ
Step3 Click Login
NOTE
Ÿ The default user name is Admin. The default password is 1234.
Ÿ It is advised to restart the device three minutes later after
modifying password to ensure modified successfully.
Ÿ User can change the system display language on the login page.
, the main page is displayed.
4.2 Modify IP address
Choose Configuration > Device > Local Network, the Local Network
page is displayed.
Input the IP address in the IP Address box and click Apply as shown in
figure 4-2.
After the IP address is set successfully, please use the new IP address
to login the Web interface.
Figure 4-2 Local Network
Figure 4-1 Login
Quick Configuration(e.g IE)
4
Step 4 Plug the network access port into interface by using the
tool, as shown in figure 3-3; The power supply of the
multi-head cable and other port to interface pass through
the rubber stopper by using screw driver or L hexagonal
wrench.
Horizontal
rotating
350°
Vertical
rotating 80°
Lens axis
rotating
350°
slotted
screw
Figure 3-3 Installing housing
NOTE
Ÿ During adjusting lens, the image might be blur, set the focus
value in Sensor > Lens control page in web page.
Step 6 Connect the camera to monitor, loosen the screws of
support frame, as shown in figure 3-5. Adjust the three
axes to focus image on monitoring scenarios. Tighten the
screws to finish adjustment.
Figure 3-2 Installation
Self-tapp ing screws
The bump
12V Power
supply
Network por t
Alarm/Audio
interface
NOTE
Ÿ There are two outlet mode of cable, for the top outlet mode, user
should drill the hole at first for threading cable.
Ÿ The side outlet mode that the installation sticker’s gap should
align the outlet rubber stopper.
Side outlet
rubber stop per
Set sc rew
Block
Figure 3-5 adjust lens
Step 7 Arrange the cable of camera to over-line buckle, then
assemble the dome cover with hex wrench, as shown in
figure 3-6.
hexagonal wrench
Installation Steps:
Step 1 Stick the Installation location sticker which is in accessory
package on the ceiling or wall. Drill three holes based on
the marks on the sticker. Drive the plastic anchors into the
holes.
Step 2 Use the wrench in the accessory package to unscrew the
three screws on the dome cover. The camera is opened,
as shown in figure 3-1. And use release the base panel
To avoid moisture influence, install the dome cover at least
half an hour after the camera is installed and powered on.
Step 3 Fetch three black self-tapping screws from the accessory
package. Then fix the screws to fasten the base panel of
camera on the ceiling as shown in figure 3-2.The position
of hook should be put at the appropriate place, which
should pass the bump as shown in figure 3-2.
Figure 3-1 Opening camera
The vandal dome camera can be installed in the ceiling, wall,
wall bracket or ceiling bracket. This section describes how to
install the camera in the ceiling.
WARNING
3
Device Installation
Plastic
anchors
Local Network
Network Card ID
IP Protocol
DHCP
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server
MTU(1280-1500)
Refresh
Apply
1500
192.168.0.120
255.255.255.0
192.168.0.1
1
IPv4
http://19 2. 16 8.0.120
1 Personnel Count: User can query the data of personnel count,
through year, month, day. The statistics can be downloaded. The
data can be shown by line chart, histogram, list.
2 AI Live video: Click the icon to view the snapshots of human face
or license plate (click “Face” or “Plate” to switch ).
The bottom page will show the captured images of vehicle and
human face.
4.4 Intelligent Analysis
At "Configuration > Intelligent Analysis" interface, user can set the
parameters of Perimeter, Single Virtual Fence, Double Virtual Fence,
Multi Loiter, Converse and Personnel Count, as shown in figure 4-7 .
Figure 4-7 Intelligent Analysis
4.5 AI Multi object
At “Configuration > AI Multi object” interface, user can enable face
detection, full body detection, vehicle detection, set the other
parameters of detection, as shown in figure 4-8.
Figure 4-8 AI Multi-object
Face Detection
Fullbody Detection
Vehicle Detection
Display Trace Info
Show Detection Area
Confidence Coefficient
Face Pixel Min(30-300)
Body Pixel Min(30-300)
Body Pixel Min(30-300)
Vehicle Pixel Min(30-300 )
Image Matting Quality
Snapshot Mode
Upload Image Interval(1-10s)
FTP Up load Image Matting
FTP Up load Whole Image
Algorithms Library Version
A
B
Pedestrian direction
15°
If user requires higher
accuracy of personnel count,
we recommend the user to
install camera and draw the
line following as figure 4-6.
Figure 4-6 Installation of personnel count
CAUTION
NOTE
For better capture performance, it is recommended to use 6mm
focus length lens or above.
Product Specifications
| Brand: | Ernitec |
| Category: | Security camera |
| Model: | 0070-08117 |
Do you need help?
If you need help with Ernitec 0070-08117, ask a question below and other users will answer you
Security camera Ernitec User Manuals
23 October 2024
15 October 2024
Security camera User Manuals
- Security camera Sony
- Security camera Xiaomi
- Security camera Bosch
- Security camera Braun
- Security camera Philips
- Security camera Panasonic
- Security camera TP Link
- Security camera D-Link
- Security camera Kogan
- Security camera Netatmo
- Security camera Lutec
- Security camera Axis
- Security camera HiLook
- Security camera Lorex
- Security camera TCP
- Security camera EMOS
- Security camera Ezviz
- Security camera Speco Technologies
- Security camera Qolsys
- Security camera Dahua Technology
- Security camera ORNO
- Security camera Hikvision
- Security camera V-Tac
- Security camera CRUX
- Security camera I-PRO
- Security camera DVDO
- Security camera Uniden
- Security camera Lumens
- Security camera BIRDFY
- Security camera EVOLVEO
- Security camera MEE Audio
- Security camera IOIO
- Security camera Arlo
- Security camera Reolink
- Security camera BirdDog
- Security camera Mobotix
- Security camera Milesight
- Security camera Flir
- Security camera KJB Security Products
- Security camera Setti+
- Security camera AVer
- Security camera Strong
- Security camera Alfatron
- Security camera Foscam
- Security camera AViPAS
- Security camera Defender
- Security camera HuddleCamHD
- Security camera Sonic Alert
- Security camera GVI Security
- Security camera DSC
- Security camera Control4
- Security camera Conbrov
- Security camera Wasserstein
- Security camera Qian
Latest Security camera User Manuals
27 October 2024
27 October 2024
27 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024