Foscam FN8108W-B4 Manual

Foscam Not categorized FN8108W-B4

Read below 📖 the manual in Italian for Foscam FN8108W-B4 (2 pages) in the Not categorized category. This guide has been helpful for 26 people and has been rated 4.5 stars on average by 2 users

Download PDF
Page 1/2
1
2
3 4 5
7 98
10
11
12
Quick Setup Guide
Security Tips
1
V1.0
305503001007
3
NVR Rear Panel
8
Software Operation
5
Placement of Wireless
IP Camera
1. Log In
2
NVR Kit Contents
8-Channel NVR
1.5m (5 ft) Ethernet Cable 4 x Bullet IP Cameras
USB Mouse
Mounting Screws
For detailed manuals, tools, etc., please visit foscam.com/downloads.
4
Wireless Connectivity
WiFi Connection
Router
Computer
HD-OUT Cable
TV
LAN
Ethernet Cable
LAN
LAN
HD-OUT
HD-OUT
Monitor
VGA Cable
VGA
VGA
HD-OUT
Foscam
Do not install the wireless NVR in humid and dusty
environment.
Put the wireless NVR in drafty environment in case of
ventilation port being blocked.
Check the power supply to avoid damage because of voltage
mismatch.
Make sure the wireless NVR working within suitable
temperature and humidity environment.
Please install the wireless NVR horizontally, and avoid
vibration.
Short circuit may occur when dust become wet on circuit
board. Please clean the dust on circuit board, connectors, and
NVR case.
Explosion may happen because of improper replacement of
battery, do not replace it by yourself; If you need, make sure it
is the same type of battery. And do not open or repair it.
Please use suitable and professional hard disk to ensure
continues and stable recording.
Lightning protection is needed when device is connected to
communication cables. Ethernet cable which comes from
outside, connecting to the wireless NVR directly is forbidden.
Right placement Wrong placement
4 x Power Adapters for Cameras
1 x Power Adapter for NVR
Quick Setup Guide
Warranty Card
2. Setup Wizard
The Setup Wizard can walk you through some important settings
on the NVR.
6
Camera Installation
Important Note:
When installing the cameras please ensure that the connection
ports at the end of the pig tail wiring are not exposed, as they
are not weather-resistant.
0~90°
0~360°
0~360°
0~90°
0~360°
0~360°
Place the cameras in your preferred locations and use the
included screws to mount them.
The shape of wireless NVR signal coverage is a ball, antenna is located in
the center. Signal is strong around antenna, and weak in the dent area of
the 2 antennas.
Based on the signal spreading ways, please make the wireless IP Camera
keeping parallel or tangent with wireless NVR, which ensure stable signal
transmission and better picture quality.
7
Powering Up
DC 12V/2A
Mouse
WiFi Connection
GND
Please make sure the voltage of power supply is matched
with wireless NVR, and ground connection work well in
socket. Connect the NVR and cameras as shown in the gures
above. Once the NVR is plugged in, press the power switch
located on the rear panel.
After the NVR starts up successfully, the Power LED indicators
will turn green, it means system runs smoothly.
DC 12V/1A
DC 12V/1A DC 12V/1A
DC 12V/1A
VGA
Monitor
VGA Cable
VGA
6
HD-OUT
VGA Output
USB
Antenna
Reset
Power Input
(DC12V / 2A)
Power Switch
Ethernet Port
GND
① Turn on the power switch on the rear panel.
After the NVR starts up successfully, the power LED and HDD
LED indicators will turn green. The startup page is displayed
on the screen.
② Change password .
For your security, please set a new password for your NVR
before Log In.
④ After modifying the password, you will be taken to the
Setup Wizard.
① Setting the time.
Uncheck the checkbox
② Format HDD. Click the Format button to set up the HDD.
Note that this will delete all les on the HDD.
HDD Full Setting. Select Stop Record and Overwrite.
③ P2P. If you want to know the UID of the device, please scan
the QR code. If you don’t want to use the Setup Wizard
next time, uncheck the Setup Wizard checkbox. Click the
Finish button to complete the setup wizard.
or Right-click→ Main Menu → Conguration → uncheck
the Setup Wizard checkbox. Click the Finish button to
complete the setup wizard.
Uncheck the checkbox
The live view interface will show you the video feed of each IP
Camera.
3. NVR adds IP Camera method
Note: The NVR and IP Camera are already paired. If you need to
match more cameras, please refer to the following steps.
F19911W is supported in this kit, besides the battery camera the
other Foscam models can be added by LAN.
① Right-click on main interface, select Pair IP Camera.
② Click Pair and press the pairing button of the camera tail cable
at the same time, until it prompts that the pairing is successful.
③ When nished code matching, The live view interface will
show you the video feed of each IP Camera.
1. Click Pair
4. Record and Playback
① Scheduled Record: Right-click → Main Menu → Record →
choose recording channel → Save (Actually, the Wi-Fi NVR
system have default set 24h scheduled recording).
③ Login page.
Enter the Username and Password, then click on the OK
button.
If you want to modify it to alarm recording, please use the left
mouse button to select the time (turned to green), if the other
channels operate in the same way, select copy.
press the
pairing button
Add F19911W:
Add Other Foscam Camera:
① Right-click on main interface, select Channel cong.
② Click Add IPC and then click Search Add.
③ Select the Camera to be added.
④ Click Add and enter the username and password for the
camera, then click on the Save.
⑤ When nished added, the live view interface will show you
the video feed of each IP Camera.
1. Click Add IPC
2. Click Search Add
4. Click Add
3. Select the camera
to be added
13 14
15
1716
19
20 21
22
18
23
24
Technical Support
13
If you have problems with your Foscam device, please contact
the reseller you purchased from, or you can e-mail the
headquarters technical support team: support@foscam.com
Your valuable comments and suggestions on improving
Foscam products are welcomed!
9
Foscam App
2. Run the Foscam APP, and then register for a
Foscam account.
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
www.foscam.com
Due to product upgrades and other reasons, this guide may be slow to
update, resulting in slight inconsistencies with the ocial website
information. Please take the ocial website(www.foscam.com)
information as the current standard.
11
Upgrade
1. You can upgrade your NVR and cameras system with local
Software.
Note:
① The upgrade le must be placed under the root directory of
the U disk.
② Don't lose power for during upgrade.
4. Preview: click device in list to enter preview interface,
select a channel to view it’s picture, as follow shows:
1. You can also simply go to the App Store or Google Play and
search for the term "Foscam". Download the APP to your
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: Room 901-902,Building 1B, Shenzhen International Innovation
Valley, Xingke 1st Street, Nanshan District, Shenzhen, Guangdong,
China, 518055
WLAN frequency range: 2400 MHz - 2483.5 Mhz.
Maximum transmission power: < 20dBm
Wireless Standard: IEEE802.11b/g/n
Power Supply: DC 12V 2.0A 24W (NVR)
DC 12V 1.0A 12W (IPC)
NVR Upgrade:
Download the rmware to the U disk → Insert U disk to NVR
USB port → Right-click→ Main Menu → Upgrade → click
Refresh → click Upgrade to upgrade your NVR.
IPC Upgrade:
Download the rmware to the U disk → Insert U disk to NVR USB
port → Right-click→ Main Menu → IPC Cong → Maintenance
→ click Refresh → click CH to update this camera or click Select
All to upgrade your all cameras.
IPC Restore default:
Right-click→ Main Menu → IPC Cong → Maintenance →
click CH to restore default this camera or click Select All to
restore default your all cameras.
Note:
Don't shut down the power during upgrade. After upgrading,
NVR restarts.
Product Performance
12
3. Device Adding: Once logged in, you can tap the "+" button
on the APP, after that scan the QR code, which is located
at the bottom of your NVR.
10
Foscam VMS
Foscam VMS is a new tool for PC. It does not require plug-ins and
is compatible with Windows & Mac, It supports all Foscam HD
cameras and up to 36 cameras at the same time. If you would
like to manage multiple cameras, we suggest you install the
Foscam VMS. You can download the “Foscam VMS” from
foscam.com/vms, and can download the "Foscam VMS" Mac
version from the APP store:
https://apps.apple.com/cn/app/foscamvms/id1521202507?mt=12
Add the NVR
1. Run Foscam VMS, then you can create a local administrator
account and login.
2. Tap the "+" button on the Foscam VMS and follow the setup
wizard to add your NVR.
Please refer to the user manual for more detailed adding steps.
3. Preview: click device in Lan Device list to enter preview
interface, select a channel to view it’s picture, click to
enter , as follow shows:
2. You can upgrade the rmware of your NVR and cameras with
Foscam App.
Open Foscam APP and Login the NVR, select Settings > NVR
Firmware or Camera Firmware Upgrade.
3. You can upgrade the rmware of your NVR and cameras with
Foscam VMS.
Open and Login Foscam VMS, select Setup > System >
System Upgrade or Camera Upgrade.
Note:
In all upgrade methods, don't shut down the power during
upgrade. After upgrading, NVR restarts.
6. Motion Detection Record
Right-click → Main Menu → IPC Cong → Advanced →
Motion Detect → Choose Enable → Set Sensitivity & Region &
Body Filter & Body Rectangle→ Apply.
7. Auto Bridge
By new mesh network auto-bridging function, without any
manual setting, wireless camera in further area will have a
judgment about the WIFI signal and auto connect to the
camera which have a better WIFI signal, to achieve more stable
and reliable video transmission.
Auto bridging is designed to expand the coverage area of
wireless signal, instead of enhancing the signal. When camera is
a little far away from NVR, or there are too many interference
factors/sources between them, camera in further area will auto
bridge/connect to the one nearby to transmit the video data.
① Right click →Pair IP Camera→ Repeater.
② Then, bridging relationship will be showed on the interface
automatically.
1.Click the button to select
the rmware to the U disk
2.Click the button to
Upgrade
1.Click the button to select
the rmware to the U disk
2.Choose the channel camera
you need to upgrade
3. Click the button to
Upgrade
1.Choose the channel camera
you need to Restore
2. Click the button to
Restore
Note: For the best experience, please update Foscam VMS to the
latest version!
Firmware upgrade step:
① Click "Download the latest rmware" button to download
the latest rmware to your computer.
② Click "Browse" button , choose le rmware version you
want to upgrade on the web page.
③ Click "Upgrade" button and wait till it's nished.
1
Basic
Device Manager
Application
System
Factory Reset
Camera Firmware
Reboot
NVR Firmware
Current firmware version：2.71.1.79
Download the latest firmware
2
Browse
Device Settings
Upgrade
3
FN7108W
FN8108H
smartphone, or scan the QR Code on the below, it will take
you to the download page to install the Foscam APP.
② Playback: Right-click → Main Menu → Playback → choose
channel and date → click timeline to check record.
5. Backup
Insert U disk to NVR USB port → Right-click→ Main Menu →
Backup → choose channel, type and time→ Search → select
target le → Backup
Note: If target le can not be searched out, please click Empty →
Add. Please remove the les which is no need before backup.
Ensure insert device (like USB) in 30 second, as system reserved
searching time for it is 30 second.

Product Specifications

Brand: Foscam
Category: Not categorized
Model: FN8108W-B4

Do you need help?

If you need help with Foscam FN8108W-B4, ask a question below and other users will answer you


Not categorized Foscam User Manuals

Foscam

Foscam FN8108W-B4 Manual

15 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals

NightStick

NightStick LGL-170A Manual

27 October 2024
Supermicro

Supermicro SuperServer ASG-2115S-NE332R Manual

27 October 2024
Phanteks

Phanteks Glacier R220C Manual

27 October 2024
Elac

Elac Protek PR-71S Manual

27 October 2024
NightStick

NightStick LGL-180-IR Manual

27 October 2024
United Office

United Office IAN 54183 Manual

27 October 2024
United Office

United Office IAN 066078 Manual

27 October 2024
United Office

United Office IAN 331845 Manual

27 October 2024
United Office

United Office ULGD 350 A Manual

27 October 2024
United Office

United Office UAVS 300 A1 Manual

27 October 2024