Hotpoint HW18HN2DAA Manual

Read below 📖 the manual in Italian for Hotpoint HW18HN2DAA (50 pages) in the Air conditioning category. This guide has been helpful for 30 people and has been rated 4.5 stars on average by 2 users

Page 1/50
SYSTEM
Duct-Free
49-5000885 Rev. 2 05-25
SAFETY INFORMATION ...... 2
REMOTE CONTROL FEATURES
AND SETTINGS-Cool only .... 3
REMOTE CONTROL FEATURES
AND SETTINGS-Heat Pump . . . 5
MANUAL OPERATION AND
MAINTENANCE ............. 7
WI-FI PAIRING .............. 8
TROUBLESHOOTING TIPS . . . 9
LIMITED WARRANTY ....... 10
OWNER’S MANUAL
ENGLISH
2 49-5000885 Rev. 2
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE SYSTEM
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
• Use this appliance only for its intended purpose as
described in this Owner’s Manual.
• This heat pump must be properly installed in
accordance with the Installation Instructions before it
is used.
• Turn the unit OFF before cleaning the air filter
• GE Appliances, a Haier company does not support
any servicing of the heat pump. We strongly
recommend that you do not attempt to service the heat
pump yourself.
• For your safety…do not store or use combustible
materials, gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance. If
you are getting rid of an old product with refrigerants,
check with the company handling disposal about what
to do.
• These R32 heat pump systems require contractors
and technicians use tools, equipment and safety
standards approved for use with this refrigerant.
DO NOT use equipment certified for R22 or R410A
refrigerant only.
WARNING
Keep batteries away from children.
• This remote controller contains batteries. If a new or
used battery is swallowed or enters the body, it can
cause severe internal burns and can lead to death
in as little as 2 hours. Always completely secure the
battery compartment. If the battery compartment does
not close securely, stop using the product, remove the
batteries, and keep it away from children.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
• The cells shall be disposed of properly, including
keeping them away from children.
• Even used cells may cause injury.
IMPORTANT SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
WARNING
•
This product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
•
Children should be supervised to ensure that they do
not play with the product.
•
Any damage of electrical supply must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
49-5000885 Rev. 2 3
Remote Control Features and Settings-Cooling Only
Applicable Model
MODEL
AC
HW12HN2CAA
HW18HN2CAA
HW24HN2CAA
Remote Control
1
8
2
11
7
4
6
9
5
10
1
1
3
7
15
3
18
1
12
6
14
TEMP
TEMP
SWING
SWING
TURBO
COOL DRY
FAN
QUIET
ECOºF/ºC
TIMER
ON
TIMER
OFF
CONFIRM
CANCEL
LOCK LIGHT RESET
1. Power Button
Press the ON/OFF button on the remote control to
start or stop the unit.
2. COOL Button
In COOL mode, the unit operates in cooling. When
FAN is set to AUTO, the heat pump automatically
adjusts the fan speed according to the room
temperature. The will be displayed during COOL
mode.
3. Fahrenheit/Celsius Button
Press °F/°C to toggle remote and unit display
temperature between Fahrenheit and Celsius.
4. Temperature +/– Buttons
Temp + : Every time the button is pressed, the
temperature setting increases. Temp – : Every time
the button is pressed, temperature setting decreases.
The operating temperature range is 60°F-86°F
(16°C-30°C).
5. FAN SPEED Button
FAN SPEED: For each press the fan speed changes
as follows:
Remote control:
Display
circulated
LOW MED HI AUTO
6. DRY Button
DRY mode is used to reduce humidity. In DRY mode,
when room temperature becomes lower than temp.
setting +2°F, unit will run intermittently at LOW speed
regardless of FAN setting. The will be displayed
during DRY mode.
7. FAN MODE Button
FAN mode circulates air only; there is no temperature
adjustment available. Use the fan speed button (5)
to adjust fan speed from low, medium to high. Auto,
Turbo and Quiet are not available. The
will be
displayed during FAN mode.
8. TURBO Button
The TURBO function is used for fastest air flow in
Heating or Cooling modes. Control will display the
TURBO icon on the bottom right side of the
remote display. Pressing the TURBO button again or
the FAN SPEED button will turn TURBO off.
9. Quiet Button
The QUIET function switches the fan to the lowest
speed. The control will display the QUIET icon on
the bottom left side of the remote display. Pressing
the QUIET button again or the FAN SPEED button will
turn QUIET off.
REMOTE CONTROL FEATURES AND SETTINGS

Product Specifications

Brand: Hotpoint
Category: Air conditioning
Model: HW18HN2DAA

Do you need help?

If you need help with Hotpoint HW18HN2DAA, ask a question below and other users will answer you




Air conditioning Hotpoint User Manuals

Air conditioning User Manuals

Latest Air conditioning User Manuals

Fujitsu

Fujitsu AUTG09LVLB Manual

27 October 2024
Fujitsu

Fujitsu ASTG09KMTC Manual

27 October 2024
Fujitsu

Fujitsu AUTG12LVLB Manual

27 October 2024
Fujitsu

Fujitsu ABTG18LVTA Manual

27 October 2024
Fujitsu

Fujitsu AUTG54LRLA Manual

27 October 2024
Fujitsu

Fujitsu ASTG22LVCC Manual

27 October 2024
Be Cool

Be Cool BC18SK2101QW Manual

27 October 2024
SHE

SHE 18KL2001F Manual

26 October 2024