Hotpoint SH6 A2Q XRD Manual

Hotpoint Refrigerator SH6 A2Q XRD

Read below 📖 the manual in Italian for Hotpoint SH6 A2Q XRD (15 pages) in the Refrigerator category. This guide has been helpful for 25 people and has been rated 4.5 stars on average by 2 users

Page 1/15
EN
1. Fan*
2. Electronic control panel / light unit
3. Bottle rack*
4. Sensor cover
5. Area shelves
6. Rating plate with commercial name
7. Fruits and vegetables crisper*
8. Door reversibility kit
9. Bottle holder*
10. Door trays
11. Door seal
* Available on selected models
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts the
operation automatically. After starting the appliance, wait
at least 4-6 hours before placing food into the appliance.
When the appliance is connected to the power supply,
the display lights up and all the icons appear on the
display for approximately 1 second. The default (factory)
values of the fridge compartment settings light-up.
HOW TO REVERSE THE DOOR SWING
- see enclosed Instructions for Use (Version_2)
Is recommended to reverse door swing by two persons.
There is not foreseen door reversibility for:
- models with integrated handle
- models with glass panel on the door.
Specifications, technical data and images may vary
from model to model
To receive the assistance call the number shown on
the warranty booklet or follow the instruction on the
web site www.hotpoint.eu
2
5
7
9
8
11
X
3
6
1
10
X
4
Read the Instructions for Use carefully before
using the appliance.
QUICK START GUIDE
ALARMS TABLE
ALARM TYPE Signal Cause Cure
Door open alarm Refrigerator Light blinks The door has remained open for more than 5 minutes. Close the door
Door open alarm Refrigerator Light OFF The door has remained open for more than 8 minutes. Close the door
Malfunction Any temperature indicators blinks Product malfunction. Contact the After-sales Service
GB
FAN
The fan improves temperature distribution inside the refrigerator compartment,
allowing better preservation of stored food.
By default, the fan is switched on.
It is advisable to keep the fan switched on when the ambient air temperature is above
27 - 28°C or if you notice drops of water on the glass shelves or in sever humidity
conditions.
To turn off the fan press the button of fan.
Please note that when the fan is switched on it will not continuously work. The fan
will start/stop working depending on the temperature and/or humidity level inside the
fridge.
It is therefore absolutely normal if the fan does not move even if the fan is switched on.
on - o
TEMPERATURE button
Press the Temperature button on the control panel to adjust the temperature from the
warmest through the lower to the coldest level.
Pressing the Temperature button, the temperature setting will change cyclically.
At first plug-in of appliance temperature setpoint is present at medium position
(factory setting).
Following table shows temperature setpoints:
Note: Displayed set points correspond to the average temperature
throughout the whole refrigerator.
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
REFRIGERATOR LIGHT
The light system inside the refrigerator compartment uses LEDs
light, allowing a better lightning as well as a very low energy
consumption.
If the LED light system does not work, please contact the
Service to replace it.
Important: The refrigerator compartment light switches on
when the refrigerator door is opened. If the door is kept open for
more then 8 minutes the light will be automatically switched off.
Indicator LEDs to display the current temperature
setpoint or the Fast Cooling function.
FAST COOLING function
The use of the Fast Cooling function is recommended:
- to increase the cooling speed of the refrigerator
compartment when placing a very high quantity of food
within it,
To activate the Fast Cooling function, press and hold
for 3 seconds the Temperature button on the control
panel till all the 3 LEDs will turn on.
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
The function is automatically deactivated after 6 hours
and return to previous selected set point. The function
can be manually deactivated by pressing and holding for
3 seconds the Temperature button on the control panel.
TEMPERATURE button
FAST COOLING button
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
Printed in Italy 08/17 - Hotpoint Ariston® Registered trademark/TM Trademark of Whirlpool, USA - © Copyright Whirlpool Europe s.r.l. 2014. All rights reserved - www.hotpoint.eu
5892140900
IT ES PT BG CS FR HU KK PL RO RU SK
UK
IT
DE
IT
1. Ventola*
2. Pannello comandi elettronico / luce
3. Mensola bottiglie*
4. Coperchio sensore
5. Zona ripiani
6. Targhetta matricola con il nome commerciale
7. Cassetto per frutta e verdura*
8. Kit reversibilità porta
9. Portabottiglie*
10. Balconcini
11. Guarnizione della porta
* Disponibile in modelli selezionati
ACCENSIONE DELL'APPARECCHIO
L'apparecchio si avvia in modo automatico, una volta
collegato l'apparecchio alla rete di alimentazione. Dopo
avere avviato l'apparecchio, attendere almeno 4-6 ore
prima di introdurre alimenti. Quando l'apparecchio viene
collegato all'alimentazione elettrica, il display si illumina
e tutte le icone appaiono sul display per circa 1 secondo.
Appaiono i valori predefiniti impostati in fabbrica per il
comparto frigorifero.
INVERSIONE DEL SENSO DI APERTURA DELLA
PORTA
- vedere le Istruzioni per l'uso allegate (Versione_2)
Si raccomanda che l'inversione del battente della porta
venga effettuata da due persone.
L'inversione del senso di apertura della porta non è
prevista per i:
- modelli con maniglia integrata
- modelli con pannello di vetro sulla porta.
Caratteristiche, dati tecnici e immagini possono
variare a seconda del modello
Per ricevere assistenza, chiamare il numero
riportato sul libretto di garanzia, oppure seguire le
istruzioni disponibili sul sito web www.hotpoint.eu
2
5
7
9
8
11
X
3
6
1
10
X
4
Prima di utilizzare l'apparecchio, leggere
attentamente le Istruzioni per l'uso.
GUIDA RAPIDA INTRODUTTIVA
TABELLA ALLARMI
TIPO DI ALLARME Segnale Causa Soluzione
Allarme porta aperta La luce frigorifero lampeggia La porta è rimasta aperta per più di 5 minuti. Chiudere la porta
Allarme porta aperta La luce del frigorifero è spenta. La porta è rimasta aperta per più di 8 minuti. Chiudere la porta
Malfunzionamento Uno degli indicatori di temperatura lampeggia Malfunzionamento del prodotto. Contattare il Servizio Assistenza
VENTOLA
La ventola migliora la distribuzione della temperatura all'interno del comparto
frigorifero, migliorando di conseguenza la conservazione degli alimenti.
La ventola è preimpostata come ATTIVA.
Si consiglia di tenere la ventola in funzione se la temperatura ambiente supera i 27-
28° C, se l'ambiente è molto umido o se si osservano gocce d'acqua sui ripiani di
vetro.
Per disattivare la ventola premere il relativo pulsante.
Tenere presente che quando è attivata, la ventola non funziona continuamente. La
ventola si attiva/si arresta in base alla temperatura e/o al livello di umidità all'interno
del frigorifero.
È pertanto assolutamente normale se la ventola è ferma anche quando è stata
attivata.
on - o
Tasto TEMPERATURA
Premere il tasto Temperatura sul pannello comandi per regolare la temperatura dal
livello più caldo a un livello inferiore, fino al livello più freddo.
Premendo il tasto Temperatura, l'impostazione della temperatura cambia
ciclicamente.
Al primo collegamento dell'apparecchio, la temperatura viene impostata sulla
posizione intermedia (impostazione di fabbrica).
La seguente tabella mostra i livelli di impostazione della temperatura:
Nota: le impostazioni visualizzate corrispondono alla temperatura media in
tutto il frigorifero.
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
LUCE FRIGORIFERO
L'illuminazione all'interno del comparto frigorifero utilizza
lampadine a LED che consentono una migliore illuminazione e
un consumo energetico molto basso.
Se il sistema di illuminazione a LED non funziona, rivolgersi al
Servizio Assistenza per la sostituzione.
Importante: la luce del comparto frigorifero si accende quando
si apre la porta del frigorifero. Se la porta viene lasciata aperta
per più di 8 minuti la luce si spegnerà automaticamente.
Indicatori LED per visualizzare l'impostazione della
temperatura o la funzione Raffreddamento rapido.
Funzione RAFFREDDAMENTO RAPIDO
L'uso della funzione Raffreddamento rapido è consigliata:
- per aumentare la velocità di raffreddamento quando
si introduce una quantità molto elevata di alimenti nel
comparto frigorifero.
Per attivare la funzione Raffreddamento rapido, premere
per 3 secondi il tasto Temperatura sul pannello comandi
fino a quando tutti e tre i LED si accendono.
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
La funzione viene automaticamente disattivata dopo 6
ore e viene ripristinata l'impostazione precedentemente
selezionata. La funzione può essere disattivata
manualmente premendo il tasto Temperatura sul pannello
comandi per 3 secondi.
Tasto TEMPERATURA
TASTO RAFFREDDAMENTO
RAPIDO
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
Stampato in Italia 08/17 - Hotpoint Ariston® Marchio registrato/Marchio TM di Whirlpool, USA - © Copyright Whirlpool Europe s.r.l. 2014. Tutti i diritti riservati - http://www.whirlpool.eu
5892140900
BGIT CS HUFR PLKK ROPT SKRU
UK
ES
GB
DE
ES
1. Ventilador*
2. Panel de control electrónico/unidad de la luz
3. Repisa para botellas*
4. Cubierta del sensor
5. Zona de repisas
6. Placa de características con el nombre comercial
7. Cajón para frutas y verduras*
8. Kit de reversibilidad de puertas
9. Sujetabotellas*
10. Bandejas de la puerta
11. Junta de la puerta
* Disponible en determinados modelos
PUESTA EN MARCHA DEL ELECTRODOMÉSTICO
El electrodoméstico se pone en marcha
automáticamente al enchufarlo. Después de poner en
marcha el electrodoméstico, espere al menos 4-6 horas
antes de colocar alimentos en su interior. Cuando el
electrodoméstico está conectado a la red eléctrica, la
pantalla se ilumina y se ven todos los iconos durante
aproximadamente 1 segundo. Se encienden los valores
por defecto (de fábrica) del compartimento frigorífico.
CÓMO MODIFICAR EL SENTIDO DE APERTURA DE
LA PUERTA
- consulte las Instrucciones de uso adjuntas (Version_2)
Es recomendable que la modificación del sentido de
apertura de la puerta se haga entre dos personas.
No está prevista la reversibilidad de la puerta para:
- modelos con asa integrada
- modelos con panel de cristal en la puerta.
Las especificaciones, la información técnica y las
imágenes podrían variar según el modelo
Para recibir asistencia, llame al número que
aparece en la garantía o siga las instrucciones del
sitio web www.hotpoint.eu
2
5
7
9
8
11
X
3
6
1
10
X
4
Antes de usar el electrodoméstico, lea
atentamente las instrucciones de uso.
5892140900
GUÍA RÁPIDA
TABLA DE ALARMAS
TIPO DE ALARMA Indicación Causa Solución
Alarma de puerta abierta La luz del frigorífico parpadea La puerta p3-ha estado abierta más de 5 minutos. Cierre la puerta
Alarma de puerta abierta La luz del frigorífico está apagada La puerta p3-ha estado abierta más de 8 minutos. Cierre la puerta
Avería Alguno de los indicadores de temperatura parpadea Avería del producto. Póngase en contacto con el Servicio Postventa
VENTILADOR
El ventilador mejora la distribución de la temperatura dentro del compartimento del
frigorífico y permite una mejor conservación de los alimentos.
De forma predeterminada, el ventilador está encendido.
Se recomienda mantener el ventilador encendido si la temperatura del aire ambiente
es superior a 27-28 °C, o si aparecen gotas de agua en las bandejas de cristal o en
condiciones de humedad severas.
Para apagar el ventilador, pulse el botón del ventilador.
Tenga en cuenta que, cuando está encendido, el ventilador no funciona
continuamente. El ventilador se pone en marcha o se para en función de la
temperatura o del nivel de humedad dentro del frigorífico.
Por tanto, es completamente normal que el ventilador no gire, incluso si está
encendido.
on - o
Botón DE TEMPERATURA
Pulse el botón de Temperatura en el panel de control para ajustar la temperatura
desde el nivel más cálido hasta el más frío.
Al pulsar el botón de Temperatura, el ajuste de la temperatura cambiará
cíclicamente.
La primera vez que conecte el electrodoméstico, el ajuste de la temperatura se fija
en la posición intermedia (ajuste de fábrica).
En la tabla siguiente se muestran los puntos de ajuste de la temperatura:
Nota: Los puntos de ajuste mostrados se corresponden con la temperatura
media en todo el frigorífico.
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
LUZ DEL FRIGORÍFICO
El sistema de iluminación del interior del compartimento
del frigorífico emplea luces LED, lo que permite una mejor
iluminación y un consumo energético muy bajo.
Si el sistema de iluminación LED no funciona, póngase en
contacto con Servicio de Asistencia para su sustitución.
Importante: La luz del compartimento frigorífico se enciende
cuando se abre la puerta del frigorífico. Si se deja la puerta
abierta durante más de 8 minutos, la luz se apaga de forma
automática.
Los indicadores LED muestran el punto de ajuste
actual de la temperatura o la función Frío rápido.
Función FAST COOL
Se recomienda el uso de la función Frío rápido:
- para aumentar la velocidad de refrigeración del
compartimento frigorífico cuando coloque una gran
cantidad de alimentos en el interior,
Para activar la función de enfriamiento rápido, pulse
el botón Temperatura del panel de control durante 3
segundos hasta que los tres LED se enciendan.
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
La función se desactiva automáticamente después
de 6 horas y vuelve al punto de ajuste seleccionado
anteriormente. Esta función se puede desactivar de forma
manual pulsando el botón Temperatura del panel de
control durante 3 segundos.
Botón DE TEMPERATURA
Botón de FRÍO RÁPIDO
Led ON Led OFFLed ON Led OFF
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
Impreso en Italia 08/17 - Hotpoint Ariston® Marca registrada/TM Marca registrada de Whirlpool, USA © Copyright Whirlpool Europe s.r.l. 2014. Todos los derechos reservados - http://www.whirlpool.eu
ES BG CSIT HUFR PLKK ROPT SKRU
UK
GB
DE

Product Specifications

Brand: Hotpoint
Category: Refrigerator
Model: SH6 A2Q XRD

Do you need help?

If you need help with Hotpoint SH6 A2Q XRD, ask a question below and other users will answer you




Refrigerator Hotpoint User Manuals

Refrigerator User Manuals

Latest Refrigerator User Manuals

Bosch

Bosch KIN85NSE0G Manual

27 October 2024
LG

LG GN-B563YC Manual

27 October 2024
Electrolux

Electrolux ETM3600 Manual

27 October 2024
Electrolux

Electrolux ESE6107 Manual

27 October 2024
Electrolux

Electrolux ETM3900 Manual

27 October 2024
Electrolux

Electrolux ERM4307 Manual

27 October 2024
Electrolux

Electrolux ETM5207 Manual

27 October 2024