HuddleCamHD HCM-1 Manual

Read below 📖 the manual in Italian for HuddleCamHD HCM-1 (2 pages) in the Not categorized category. This guide has been helpful for 24 people and has been rated 4.5 stars on average by 2 users

Page 1/2
Step 2
Screw mount to pipe securely, engag-
ing a minimum of 1/2” of pipe into
mount (Fig 4). When aligned to desired
locaon, ghten set screw (Fig 1, #2)
to 30-36 in-lbs of torque (this is ap-
proximately when the set screw will
stop moving and the long arm of the
long arm hex wrench(Fig 1, #3) will
start to bend slightly).
Whats Included
QTY 1—Small Ceiling Mount BK/WH
QTY 11/4"-20x 3/8" PPH and QTY 21/4” Machine Screw Flat Washer (Fig 1, #1)
QTY 110/32 x 1/4” cup point set screw (Fig 1, #2)
QTY 1 3/32” long arm hex wrench (for set screw) (Fig 1, #3)
#1
#2
#3
Fig 1
Rev 2.1
5/15/2020
HCM-1C
Small Base Camera
Ceiling Mount
Setup Guide
Mounng Instrucons
Step 1
Screw 1” NPT pipe, or pipe nipple, to a properly
installed mounng plate or pipe ange (Fig 2).
Tighten unl pipe can no longer be ghtened with
a pipe wrench.
If using a 1.5” plate or ange you must us a 1.5” -
1” reducing bushing (Fig 3).
NOTE: Plate/ange, reducer bushing and 1” NPT
pipe or nipple are not included.
Fig 3
Fig 2 Fig 4
For more informaon on HuddleCamHD
mounts and other products please visit:
hps://huddlecamhd.com/
Rev 2.1
5/15/2020
HuddleCamHD
HC-WEBCAM-94
HC-GO
HC-EPTZ-XXX
HC3X-XX-G2
HC3XA-XX
HC3XW-XX-G2
HC10X-USB2-XX
HC10XA-XX
HC10X-XX-G3
HC20X-XX-G2
Step 4 / 4
Pass cabling through pipe or dress
to outside of pipe and connect for
a clean installaon.
Mounng Instrucons Connued...
Mount Compability
Step 3 / 4
Mount camera upright to top of mount
or invert to boom of mount with includ-
ed 1/4-20 machine screw. (Fig 1, # 1) U-
lize (0,1,2) 1/4” machine screw at wash-
ers as required. (Fig 1, #1) Note: 1/4”
machine screw at washers are to be
used depending upon depth of thread
insert in base of camera, in order to
achieve a snug t.
Other Cameras
This mount has been
designed for use with most
small based cameras ulizing
a 1/4-20” mounng hole as
can be found on SONY,
Panasonic, Cisco, Polycom
and Vaddio cameras.
PTZOpcs
PT-WEBCAM-80
PTEPTZ-XXX-ZCAM
PTVL-XXX-ZCAM
PT12X-XXX-ZCAM
PT20X-XXX-ZCAM
PT12X-XXX-XX-G2
PT20X-XXX-XX-G2
PT30X-XXX-XX-G2

Product Specifications

Brand: HuddleCamHD
Category: Not categorized
Model: HCM-1

Do you need help?

If you need help with HuddleCamHD HCM-1, ask a question below and other users will answer you




Not categorized HuddleCamHD User Manuals

Not categorized User Manuals

Latest Not categorized User Manuals