Jilong JL020256-1N Manual
Jilong
air mattress
JL020256-1N
Read below 📖 the manual in Italian for Jilong JL020256-1N (21 pages) in the air mattress category. This guide has been helpful for 32 people and has been rated 4.5 stars on average by 2 users
Page 1/21
1
Important Safety Guideline
Please read, understand and follow all instructions prior to using.
To enhance the enjoyment of your Air Bed and protect the safety of the operator
using the product, ALWAYS STRICTLY OBSERVE the following important
safety points. The following important points should be read and understand
before using this product:
1. WARNING: Only for indoor household use. Keep away from fire.
2. RISK OF COMBUSTION: Do not place the airbed against or near any
open flames, heaters, furnaces or other hot objects.
3. WARNING: Do not obstruct the air passage opening or insert any objects
into the opening at any time.
4. WARNING: Do not stand, jump or use the airbed as a trampoline. Always
supervise children near the Airbed.
5. WARNING: This product is not a raft or floatation device. Do not use near
or on water.
6. WARNING: Children must not be left unattended when using the Airbed.
Use only under adult competent supervision.
7. WARNING: Keep pets away from the Airbed. Pets may tear or puncture the
airbed.
8. IMPORTANT: Make sure the area is flat, smooth, even and free of sharp
objects that can puncture the airbed. Do not set up the Airbed near to stairs,
doors, drops, sharp edges or breakables.
9. IMPORTANT: To minimize any chance of rolling, tipping or swaying,
avoid sleeping on the edge of the airbed. Edges provide less support than the
middle of the Airbed.
10. IMPORTANT: Children should be supervised to ensure that they do not
play with the appliance.
11. WARNING: The storage bag (if included) is not a toy. To avoid danger of
suffocation, keep the airbed storage bag or any other bags away from babies
and children. Fold up the bag and store away from children when not in use.
Airbed Instruction Manual
BAB-12-E
2
Inflation
1. Unfold your product and lay flat. Make sure the flocked side is upturned
during the inflation.
2. You can use foot or hand pump (not including) to inflate the airbed.
TIP: How to use the 2-in-1 inflatable valve
Pull out the base valve from the main chamber, open the top stopper of
the valve（See A）.
Insert the inflation hose and inflate the chamber（See B）. Once inflation is
finished, insert the top stopper to the base valve（See C）.
WARNING: Do not use air compressor or high pressure pumps. Do
not over inflate: excessive inflation of the air chambers can cause the
chamber to burst or cause damage to the welding seams.
Deflation
Pull out the base valve from the bed (C), open the cover (B) and take out
the stopper to release air (A). Do not to puncture your Airbed. Do not force
air out of the Airbed. Allow air to escape slowly and naturally. Fold
carefully and re-insert into the package. See below illustration!
3
Storage and Maintain
1) Clean the product with clear water, then leave it in shady and cool place for
airing, fold it into original package and place it indoor for next use. Caution:
Do not use the alkali or acid detergent to clean product! Do not leave product
exposed under sunlight directly because it will shorten the using-life of
product.
2) Fold the airbed loosely and avoid sharp bends, corners and creases which can
damage the airbed.
3) No specific maintenance is required for electric pump.
4) Place the airbed inside the storage bag and store in a dry and room
temperature location indoors. Do not store in an area where it is likely to be
exposed to extreme temperature.
Repair Patch Instructions
Small pinhole and small puncture leaks can be repaired with the included repair patch
a) Locate the leak place.
b) Deflate and drain the water.
c) Clean the area surrounding the leakage and wipe up all water from the surface.
d) Take out the repair patch, cut it into required shape and size, which should be litter
larger than the leaking area, put the patch on leaking area and press firmly.
e) You can use it again after 24 hours drying of the repaired position.
If the damage is bigger than 1” (2.5cm), we recommend using a Silicone or rubber
based glue for repair. Please read warning statement on glue prior to use.
Shanghai Jilong Plastic Products Co. Ltd.
No. 460 Lanxue Road, Huanglou, Pudong Area, Shanghai, 201205, P.R. China
Tel: +86-21-58942200 E-mail: info@jilong.com Web: www.jilong.com
Product Specifications
| Brand: | Jilong |
| Category: | air mattress |
| Model: | JL020256-1N |
Do you need help?
If you need help with Jilong JL020256-1N, ask a question below and other users will answer you
air mattress Jilong User Manuals
14 October 2024
14 October 2024
14 October 2024
14 October 2024
air mattress User Manuals
Latest air mattress User Manuals
26 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024