Khind EI502 Manual
Read below 📖 the manual in Italian for Khind EI502 (18 pages) in the Iron category. This guide has been helpful for 22 people and has been rated 4.5 stars on average by 2 users
Page 1/18
KHIND CARE Mobile App
1-800-88-0032
khind.com.my
Download to register for
E-Warranty & enjoy hassle-
free after-sales services.
ELECTRIC
STEAM
IRON
EI502
U S E R M A N U A L
Please read this manual carefully before operating this product.
Keep this manual handy for further reference.
IMPORTANT
P/N: 40-51652-00
1. Read the instruction manual carefully and follow the instruction closely.
2. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
3. Use this appliance with specified voltage as stated on the rating label. Before connecting
the appliance to AC mains, made sure the voltage specified corresponds to the AC supply
to your house.
4. This appliance is intended for household use only; commercial use will void warranty.
5. Do not handle the plug and the appliance with wet hands.
6. Do not pull, lift, or carry the appliance by its power cord. Do not excessively bend, stretch,
twist, haul and tramp the power cord or place heavy objects on it.
7. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
8. With any indication of damage or malfunction, please stop using the appliance
immediately to avoid hazards. Take it to the authorized service centre for repair. Do not
attempt to repair or change any parts by yourself.
9. Always take the appliance by its handle and warn against possible hazards. Eg: scalding
or burns
10. The power cord should not touch the soleplate when it is hot.
11. Do not touch the soleplate when the iron is operating or after operation.
12. Never immerse the appliance in water to protect against electrical shock hazard.
13. Keep the soleplate smooth; avoid contact with hard objects.
14. Do not leave the appliance unattended while it is connected to the main power outlet.
15. Do not iron over zippers, buttons or any form of metal ornaments found on clothes as they
may scratch the soleplate.
16. Do not bend the power cord or wind it round the appliance.
17. Never drop the appliance. If the appliance was dropped, do not use the appliance;
If there are visible signs of damages or if it is leaking, please deliver to service centre
for servicing.
18. Always disconnect the appliance from electrical outlet when not in use or before cleaning
or before filling the water tank with water.
19. The appliance must be used and rested on a flat stable surface.
20. Only fill in water but no other liquids or additives.
21. Never put the appliance down on its soleplate during use. When placing the appliance on
its stand, ensure that the surface on which the stand is placed is stable.
Safety Precaution Information
1
Safety & Warning Information
2
Cleaning & Maintenance
1. Make sure the appliance has cooled down and unplugged from power supply
before cleaning.
2. Starch and other residue may be easily removed from the soleplate with damp cloth.
3. Do not use abrasive, steel wool or metal implements to clean the soleplate.
Parts Identification
1. Spray Nozzle
2. Water Inlet
3. Self-Clean Button
4. Steam Control
5. Power Steam Button
6. Spray Button
7. Power Cord
8. Swivelling Cord Protector
9. Temperature Pilot Light
10. Water Tank
11. Temperature Control
12. Soleplate
*Pictures are for illustration purposes only.
1
2
3
11
10
9
7
8
12
4
5
6
Model
Voltage
Power
Power Cord Length
Steam Rate
Water Tank Capacity
Net Weight
Product Dimension (LxWxH)
EI502
220-240V ~ 50/60Hz
1300-1500W
1.8m
10g/min
220ml
0.7kg
240 x 100 x 121mm
Specifications
*Specifications are subject to change without prior notice.
3
How to Use
Operation
A. Before First Use
Peel off the protective foil from the soleplate and wipe the soleplate with a soft cloth.
B. Filling the Water Tank
Warning! Make sure the appliance is not connected to the power supply before filling
the tank with water.
1. In order to avoid early furring up, we recommend to use distilled water only.
2. Make sure the Steam Control set to “ 0 “ (Steam off)
3. Open the Water Inlet
4. Fill in water (no additives) up to the maximum filling mark indicated on the water tank.
5. Close the Water Inlet.
Note: Empty the Water Tank after use.
C. Connection to the Power Supply
1. After connecting to power supply, the Temperature Pilot Light will light up while the
appliance heating up.
2. It goes off as soon as the appliance reaches pre-set temperature and you may now
start ironing.
3. During ironing, the Temperature Pilot Light automatically turn on and off as the
appliance heats up / reaches to the pre-set temperature.
D. Setting the Temperature
Set the Temperature Control according to the international textile protection symbols
(located on the Temperature control and washing label of the garment)
Rayon, Acrylic – Low Temperature
Silk, Wool – Medium Temperature
Cotton, Linen – High Temperature
E. Steam Ironing
Note: The appliance works at a constant steam volume, i.e., the steam pressure stays
same regardless of the filling level in the Water Tank.
1. Adjust the Temperature Control to the desired setting.
2. Set the steam on using the Steam Control.
3. If steam escapes from the Soleplate when the appliance is held horizontally, it is ready
for stream ironing.
4. To steam iron delicate synthetics, set the Temperature Control to a medium temperature
level. Once the Temperature Pilot Light has gone out, set the Steam Control to the
steam setting. Hold the appliance horizontally first to see whether steam is produced.
Then start ironing (check the setting at a hidden area of the garment). As the steam
produces a kind of barrier between the soleplate and cloth, most textiles are suitable
for steam ironing.
F. Power Steam
1. Press the Power Steam Button to generate a power burst of steam that can penetrate
the fabrics and smoothen the most difficult and tough creases. Wait for a few seconds
before pressing again.
2. It is also possible to use the power steam for straightening hanging clothes (vertical
shot of steam). Press the Power Steam Button in intervals then.
4
Note: If water drips from the Soleplate, its temperature might be too low. Either increase
the temperature or wait for a few seconds before pressing the button again to let the
Soleplate heat up.
G. Spray
Use the spray function to iron out stubborn creases at any temperature. Simply press the
Spray Button when required. Make sure there is enough water in the Water Tank.
H. Dry Ironing
For dry ironing, set the Steam Control to 0 (Steam off).
If you put down the iron in an upright position, steam production stops as well.
I. Self-Cleaning
Regularly clean the steam iron depending on the frequency of use and the local water
quality. In case of rather hard water self-cleaning is recommended at least every 2 weeks.
1. Set the Steam Control to “0” (steam off).
2. Set the Temperature Control to the highest level.
3. Open the Water Inlet and fill water up to the maximum filling mark into the Water Tank.
Close the Water Inlet.
4. Connect the power plug of the appliance to the wall socket.
5. Let the appliance heat up until the Temperature Pilot Light goes out.
6. Disconnect the power plug.
7. Hold the appliance horizontally across a sink.
8. Push the Steam Control to Self-Clean. Boiling hot water and steam come out of the
Soleplate washing out any limescale. Sway the iron to and fro during this.
9. Set the Steam Control to “0” (steam off).
10. Wipe the Soleplate on a (preferably) old piece of cloth. Connect the power plug to the
wall socket again and let it heat up. Any residual water now evaporates through the
Soleplate.
11. Unplug the appliance and let it cool down before stowing it away.
J. Storage
1. Unplug the appliance and let it cool down.
2. Set the Temperature Control to the lowest level.
3. Empty the Water Tank.
4. 1. Set the Steam Control to “0” (steam off).
5. If necessary, wipe the appliance with a damp cloth.
6. Store the appliance out of the reach of children and in a clean and dry place.
K. Useful Tips / Advice
1. When the appliance is used for the first time, some smoke may be generated. This is
quite normal and stops shortly after having started ironing.
2. Damp clothes are easier to iron than fully dry clothes.
3. Before the first use or when the appliance has not been used for some time, hold it
horizontally and let steam escape for approx. 1 minute by pressing the Power Steam
Button several times.
4. When using spray starch, we recommend wiping the Soleplate from time to time to
avoid the build-up of any residues.
Product Specifications
| Brand: | Khind |
| Category: | Iron |
| Model: | EI502 |
Do you need help?
If you need help with Khind EI502, ask a question below and other users will answer you
Iron Khind User Manuals
13 October 2024
13 October 2024
Iron User Manuals
- Iron Electrolux
- Iron Bosch
- Iron Braun
- Iron Philips
- Iron Panasonic
- Iron Melissa
- Iron Cecotec
- Iron Imarflex
- Iron Create
- Iron G3 Ferrari
- Iron Sunbeam
- Iron Conair
- Iron Orbegozo
- Iron Sencor
- Iron Hyundai
- Iron Ufesa
- Iron Rowenta
- Iron Tower
- Iron Eldom
- Iron Elba
- Iron Brentwood
- Iron Black And Decker
- Iron Hamilton Beach
- Iron Di4
- Iron Mellerware
- Iron Izzy
- Iron Polti
- Iron Girmi
- Iron Camry
- Iron DPM
- Iron Qilive
- Iron Proficare
- Iron Lenoxx
- Iron Hacienda
- Iron Yamazen
Latest Iron User Manuals
26 October 2024
26 October 2024
26 October 2024
26 October 2024
25 October 2024
25 October 2024
23 October 2024
23 October 2024
23 October 2024
22 October 2024