Primera AP380 Manual

Primera Labelprinter AP380

Read below 📖 the manual in Italian for Primera AP380 (37 pages) in the Labelprinter category. This guide has been helpful for 26 people and has been rated 4.5 stars on average by 2 users

Download PDF

Page 1/37

For the most recent version of this manual please visit

https://www.primera.com/applicatordownloads

User's Manual

091224

Page | 2

Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS MADE WITH

REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this

document may be photocopied, reproduced, or translated into another language without prior written consent.

Trademark Acknowledgments: Primera and Primera Eddie are registered trademarks of Primera Technology, Inc. Windows is

a registered trademark of Microsoft Corporation. All other trademarks are the property of their respective owners.

Revision History

FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

For Users in the United States: This product is intended to be supplied by a UL listed Direct Plug-In Power Supply marked

"Class 2" or a UL listed ITE Power Supply marked "LPS" with output rated 12VDC, 3A or higher. This equipment has been

tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. In a domestic

environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cables is required to comply with the Class A limits of Part 15 of the FCC Rules. You are cautioned that any

changes or modifications not expressly approved in this manual could void your authority to operate and/or obtain warranty

service for this equipment.

For Users in Canada: This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on

the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n'emet

pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class A prescrites dans le

Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.

! WARNING !

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE EXTERIOR PANELS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL. OPERATE THE UNIT WITH ONLY THE PROPER ELECTRICAL SPECIFICATIONS AS LABELED

ON THE PRINTER AND AC ADAPTER.

! WARNING!

DO NOT WEAR LOOSE-FITTING CLOTHING SUCH AS NECK TIES OR LOOSE LONG SLEEVES WHEN OPERATING THE AP380.

THE MOTOR IS VERY POWERFUL AND THE LINER DRIVE ROLLER COULD CATCH THE CLOTHING WHILE THE LABELS ARE

BEING APPLIED.

Page | 3 
 
Table of Contents   
 
Section 1: Unpacking and Setup ..................................................................................................... 4 
Section 2: Assemble the Liner Rewinder ........................................................................................ 6 
Section 3: Loading the Label Stock ............................................................................................... 11 
Section 3: Loading the Container .................................................................................................. 21 
Section 4: Applying the Label ....................................................................................................... 25 
4A. Apply the Label .................................................................................................................... 25 
4B. Apply Two Labels to the Same Container ............................................................................ 25 
4C. Calculate Distances for Two-Label Mode ............................................................................ 26 
4D. Count Labels (AP380 only) .................................................................................................. 26 
Section 5: Settings Overview ........................................................................................................ 27 
5A. Application Speed ............................................................................................................... 27 
5B. Label Counter Mode ............................................................................................................ 27 
5C. Label Application Modes ..................................................................................................... 27 
5D. Container Roller Modes ...................................................................................................... 28 
5E. Units of Measure/Firmware Display .................................................................................... 28 
5F. Label Load Mode .................................................................................................................. 29 
5G. Single Label Feed ................................................................................................................. 29 
5H. Display Intensity .................................................................................................................. 29 
Section 6: Label Path Diagram ...................................................................................................... 31 
Section 7: Troubleshooting and Maintenance .............................................................................. 32 
7A. Troubleshooting .................................................................................................................. 32 
7B. Maintenance ....................................................................................................................... 34 
Section 8: Specifications ............................................................................................................... 37 
Section 9: Certifications and Environmental Policy ...................................................................... 38 
 
 
   