SentrySafe QAP2EL Manual
SentrySafe
Vault
QAP2EL
Read below 📖 the manual in Italian for SentrySafe QAP2EL (19 pages) in the Vault category. This guide has been helpful for 26 people and has been rated 4.5 stars on average by 2 users
Page 1/19
XL Quick Access Pistol Safe
Owner’s Manual
QAP2BEL
QAP2E/ QAP2EL
2 3
English
Table of ContentsWarnings
WARNING
SentrySafe recommends that you do not store loaded guns in this unit.
NOTICE
YOUR SAFE IS ONLY PART OF YOUR TOTAL SECURITY PROTECTION.
SentrySafe recommends that you store your safe in a closet, office, basement, bedroom or any
other location that is convenient for you but out of direct line of sight from prying eyes.
The location of the safe does not affect the safe’s ability to protect your valuables inside.
This is a California-approved firearm safety device that meets the requirements of Penal Code
section 23655 and the regulations issued thereunder.
REGISTRATION
www.registermysafe.com
Reasons to register: By registering your SentrySafe Product you can easily retrieve forgotten
codes and combinations, which would otherwise require a notary letter and payment.
Thank you for your purchase of a Sentry
®
Safe Product. SentrySafe is committed to securing,
organizing and protecting your most important documents, valuables and keepsakes.
Français ........................................................................................................................11
Español ......................................................................................................................... 23
English
Warnings ..................................................................................................................... 2
Registration ................................................................................................................. 3
Prepare for First Time Use ............................................................................................. 4
Programming Your Safe ............................................................................................. 4-5
Programming Interior LED Light (QAP2EL and QAP2BEL) ............................................... 6
Locking and Unlocking Your Safe .................................................................................. 7
Bolt-Down Instructions ................................................................................................. 8
Troubleshooting ........................................................................................................... 9
Customer Service........................................................................................................ 10
IMPORTANT
If you experience problems or challenges with your safe, please contact us.
Many issues can be quickly resolved without the product being returned.
For videos, instructions & Frequently Asked Questions (FAQs),
visit: www.sentrysafe.com
1 2 3 4
4 5
English
NOTE: Store code and keys in a secure location (other than in the safe).
NOTE: SentrySafe offers a secure on-line location for the entry and retrieval of your code.
Go to www.registermysafe.com and register your safe.
Insert key into keyhole and turn clockwise.
NOTE: Do not lock key inside safe – this is an override key and will
open the safe in the event that you have lost your code.
A
Remove the battery pack cover.
B
Pull out battery pack (keep battery pack connected
to wires).
C
Insert four NEW AA alkaline batteries.
IMPORTANT
All safe models initially work with the factory code 1, 2, 3, 4, 1. It is therefore
important to re-program your safe with a new user code you have personally
selected to provide maximum security.
The XL Quick Access Pistol Safe comes with a built-in code.
Factory code 1, 2, 3, 4, 1.
Press any button once to bring the safe out of standby mode, then
enter the Factory Code 1, 2, 3, 4, 1.
The Green LED will light.
To Program an Electronic Code
A
Find the Reset button located behind the battery pack.
B
Press and hold the Reset button until the keypad flashes 3 times.
The LEDs remain on to indicate it is ready to accept a new user code.
C
Enter a user code that is four, five or six digits long.
D
A successful programming of the user code is indicated when the
LED light flashes green three times.
Programming Your Safe
Preparing your safe for first-time use
Programming your safe
Programming Your Safe
NOTE: Do not use rechargeable batteries or any other type of non-alkaline battery.
Do not mix old and new batteries. Do not mix alkaline and standard batteries.
To Change an Electronic Code
A
Press and hold the Reset button until the keypad flashes 3 times.
B
Enter a new user code that is four, five or six digits long. The safe
will then automatically erase the previous user code.
NOTE: Write down your user code, and keep it in a secure location.
Or visit www.registermysafe.com to store your user code.
–OR–
To Program Primary User Fingerprints on Models
with Biometric Lock
(Up to four fingerprints can be programmed)
A
Press and hold the Reset button until the keypad flashes 3 times.
The LEDs will remain on to indicate that the safe is ready to
accept two new fingerprints.
B
Swipe the first finger across the fingerprint scanner multiple
times. The LED light will flash green once for each valid scan.
C
When enough valid scans have been recorded (usually 5-10
scans), there will be a brief pause and the LED light will flash
green 3 times to indicate successful programming.
D
Immediately add a second fingerprint following the registration
of the previous one. Repeat steps B and C as indicated above.
To Program Secondary User Fingerprints
A
Press and hold the Reset button until the keypad flashes 3 times. Once the LEDs remain
on, press and hold the Reset button again until the LEDs flash. The LEDs will remain on to
indicate that the safe is ready to accept two new fingerprints.
B
Repeat steps B, C and D as indicated under: To Program Primary User Fingerprints
To Erase Fingerprints
A
Press and hold the Reset button until the keypad flashes 3 times. The LEDs remain on to
indicate the safe is ready to erase fingerprints.
B
Swipe a programmed fingerprint once and wait 10 seconds. The red LED will flash 3 times to
indicate all programmed fingerprints have been erased.
NOTE:
- The user code or fingerprint programmed will not be erased when the battery power is removed.
- If you program a four or five digit user code, then you will need to wait 10 seconds until your
code is accepted. This is only valid during the setup of your safe. If you program a six digit user
code, then the light will immediately turn green.
- If the red LED flashes 3 times, programming failed.
- When you are finished programming your safe, replace the battery pack cover.
A
Product Specifications
| Brand: | SentrySafe |
| Category: | Vault |
| Model: | QAP2EL |
Do you need help?
If you need help with SentrySafe QAP2EL, ask a question below and other users will answer you
Vault SentrySafe User Manuals
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
13 October 2024
Vault User Manuals
Latest Vault User Manuals
26 October 2024
23 October 2024
22 October 2024
22 October 2024
21 October 2024
20 October 2024
19 October 2024
19 October 2024
19 October 2024
15 October 2024