Adwa AD100 Manual
Adwa
Measuring equipment
AD100
Read below 📖 the manual in Italian for Adwa AD100 (2 pages) in the Measuring equipment category. This guide has been helpful for 26 people and has been rated 4.5 stars on average by 2 users
Page 1/2
ERROR MESSAGES
Ec: use a fresh buffer solution.
Eb: batteries should be replaced.
SPECIFICATIONS
AD100
Range -2.0 to 16.0 pH
Resolution 0.1 pH
Accuracy ± 0.1 pH
Temp.compensation Automatic
Environment 0 - 50 °C
95 % Relative
Humidity
Battery Life/Type 250 Hrs./4x1.5 V
Dimensions 173 x 41 x 22 mm
AD101
Range -2.00 to 16.00 pH
Resolution 0.01 pH
Accuracy ± 0.02 pH
Temp.compensation Automatic
Environment 0 - 50 °C
95 % Relative
Humidity
Battery Life/Type 250 Hrs./4x1.5 V
Dimensions 173 x 41 x 22 mm
USER MANUAL
AD100 & AD101
pH Testers
• Microprocessor-based pH tester
• Automatic temperature compensation
• Splash-proof keypad
• Automatic shut-off
ACCESSORIES
AD70004P pH 4.01 buffer solution
20 ml sachet (25 pcs.)
AD70007P pH 7.01 buffer solution
20 ml sachet (25 pcs.)
AD70010P pH 10.01 buffer solution
20 ml sachet (25 pcs.)
Dear Customer,
Thank you for choosing an ADWA product.
Please read carefully this manual before
starting operations.
For additional technical information, please
e-mail us at:
sales@adwainstruments.com
ISTRAD100 09/14
www.adwainstruments.com
ERROR MESSAGES
Ec: use a fresh buffer solution.
Eb: batteries should be replaced.
SPECIFICATIONS
AD100
Range -2.0 to 16.0 pH
Resolution 0.1 pH
Accuracy ± 0.1 pH
Temp.compensation Automatic
Environment 0 - 50 °C
95 % Relative
Humidity
Battery Life/Type 250 Hrs./4x1.5 V
Dimensions 173 x 41 x 22 mm
AD101
Range -2.00 to 16.00 pH
Resolution 0.01 pH
Accuracy ± 0.02 pH
Temp.compensation Automatic
Environment 0 - 50 °C
95 % Relative
Humidity
Battery Life/Type 250 Hrs./4x1.5 V
Dimensions 173 x 41 x 22 mm
USER MANUAL
AD100 & AD101
pH Testers
• Microprocessor-based pH tester
• Automatic temperature compensation
• Splash-proof keypad
• Automatic shut-off
ACCESSORIES
AD70004P pH 4.01 buffer solution
20 ml sachet (25 pcs.)
AD70007P pH 7.01 buffer solution
20 ml sachet (25 pcs.)
AD70010P pH 10.01 buffer solution
20 ml sachet (25 pcs.)
Dear Customer,
Thank you for choosing an ADWA product.
Please read carefully this manual before
starting operations.
For additional technical information, please
e-mail us at:
sales@adwainstruments.com
ISTRAD100 09/14
www.adwainstruments.com
CONDITIONING
Remove the cap. If white crystals have
formed, they will be dissolved during
conditioning.
To condition, soak the tip of the tester in
pH 7.01 buffer solution for ten minutes.
CALIBRATION
Calibrate your tester once a week or at
any time you suspect a problem with the
readings. ADWA pH testers can be
calibrated at 4, 7 and 10 pH values.
ALWAYS CALIBRATE AT pH 7 FIRST.
1. Put the tip of the tester in pH 7.01 buffer
solution and press the ON/OFF button.
2. Press CAL button: “7.0” and “pH” will
start flashing. When the sign “pH” stops
flashing, the reading has stabilized. Then
press READ button: “4.0” and “pH” will
start flashing.
3. Rinse the tip of the tester with deionized
water.
4. Put the tip of the tester in pH 4.01 buffer
(for acidic measurements) or in pH 10.01
buffer (for alkaline measurements): “4.0”
(or “10.0”) and “pH” will start flashing.
5. When the sign “pH” stops flashing, the
reading has stabilized. Press READ. The
calibration is completed.
ALWAYS USE A FRESH BUFFER
SOLUTION FOR CALIBRATION.
OPERATION
1. Remove the protective cap from the
bottom of the tester.
2. Press ON/OFF button to turn the tester
on.
3. Place the tip of the tester into the sample
to be measured.
4. Stir the sample and record the reading
when the value has stabilized. The tester
will automatically compensate temperature
variations.
5. Press ON/OFF button to turn the tester
off.
MAINTENANCE
The sensor should be kept moist at all times.
This can be done by storing the tester with
a few drops of pH 7.01 buffer solution in
the protective cap. Rinse the electrode after
each measurement with tap water.
WARNING: DO NOT USE DEIONIZED
OR DISTILLED WATER FOR STORAGE
PURPOSES.
BATTERY REPLACEMENT
When the batteries need to be replaced,
the “Eb” error message will appear on the
display and the tester will turn off automatically
to prevent the unreliable measurement result.
Open the battery compartment at the top
of the tester. Place the batteries noting the
polarity listed in the battery compartment.
CONDITIONING
Remove the cap. If white crystals have
formed, they will be dissolved during
conditioning.
To condition, soak the tip of the tester in
pH 7.01 buffer solution for ten minutes.
CALIBRATION
Calibrate your tester once a week or at
any time you suspect a problem with the
readings. ADWA pH testers can be
calibrated at 4, 7 and 10 pH values.
ALWAYS CALIBRATE AT pH 7 FIRST.
1. Put the tip of the tester in pH 7.01 buffer
solution and press the ON/OFF button.
2. Press CAL button: “7.0” and “pH” will
start flashing. When the sign “pH” stops
flashing, the reading has stabilized. Then
press READ button: “4.0” and “pH” will
start flashing.
3. Rinse the tip of the tester with deionized
water.
4. Put the tip of the tester in pH 4.01 buffer
(for acidic measurements) or in pH 10.01
buffer (for alkaline measurements): “4.0”
(or “10.0”) and “pH” will start flashing.
5. When the sign “pH” stops flashing, the
reading has stabilized. Press READ. The
calibration is completed.
ALWAYS USE A FRESH BUFFER
SOLUTION FOR CALIBRATION.
OPERATION
1. Remove the protective cap from the
bottom of the tester.
2. Press ON/OFF button to turn the tester
on.
3. Place the tip of the tester into the sample
to be measured.
4. Stir the sample and record the reading
when the value has stabilized. The tester
will automatically compensate temperature
variations.
5. Press ON/OFF button to turn the tester
off.
MAINTENANCE
The sensor should be kept moist at all times.
This can be done by storing the tester with
a few drops of pH 7.01 buffer solution in
the protective cap. Rinse the electrode after
each measurement with tap water.
WARNING: DO NOT USE DEIONIZED
OR DISTILLED WATER FOR STORAGE
PURPOSES.
BATTERY REPLACEMENT
When the batteries need to be replaced,
the “Eb” error message will appear on the
display and the tester will turn off automatically
to prevent the unreliable measurement result.
Open the battery compartment at the top
of the tester. Place the batteries noting the
polarity listed in the battery compartment.
Product Specifications
| Brand: | Adwa |
| Category: | Measuring equipment |
| Model: | AD100 |
Do you need help?
If you need help with Adwa AD100, ask a question below and other users will answer you
Measuring equipment Adwa User Manuals
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
Measuring equipment User Manuals
- Measuring equipment EBERLE
- Measuring equipment Hazet
- Measuring equipment Fluke
- Measuring equipment Megger
- Measuring equipment Kogan
- Measuring equipment AkYtec
- Measuring equipment Voltcraft
- Measuring equipment Klein Tools
- Measuring equipment PeakTech
- Measuring equipment Clean Air Optima
- Measuring equipment Flex
- Measuring equipment CSL
- Measuring equipment Elgato
- Measuring equipment Kern
- Measuring equipment Be Cool
- Measuring equipment ORNO
- Measuring equipment Einhell
- Measuring equipment Mitsubishi
- Measuring equipment Noyafa
- Measuring equipment Megasat
- Measuring equipment Reely
- Measuring equipment Joy-it
- Measuring equipment Logilink
- Measuring equipment Basetech
- Measuring equipment Gossen Metrawatt
- Measuring equipment TFA
- Measuring equipment Owon
- Measuring equipment Extech
- Measuring equipment Milesight
- Measuring equipment Sonel
- Measuring equipment Flir
- Measuring equipment Testo
- Measuring equipment MSW
- Measuring equipment Stamos
- Measuring equipment Ideal
- Measuring equipment Hikmicro
- Measuring equipment Siglent
- Measuring equipment Kopp
- Measuring equipment PICO
- Measuring equipment Enda
- Measuring equipment Wachendorff
- Measuring equipment Ermenrich
- Measuring equipment Beha-Amprobe
- Measuring equipment Tempo
- Measuring equipment PCE Instruments
- Measuring equipment Vemer
- Measuring equipment Testboy
- Measuring equipment Duro Pro
- Measuring equipment Kyoritsu
- Measuring equipment Benning
- Measuring equipment MASIMO
- Measuring equipment Stahlwille
- Measuring equipment SHX
Latest Measuring equipment User Manuals
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024