WyreStorm EX-100-H2-EARC Manual
WyreStorm
AV extender
EX-100-H2-EARC
Read below 📖 the manual in Italian for WyreStorm EX-100-H2-EARC (2 pages) in the AV extender category. This guide has been helpful for 22 people and has been rated 4.5 stars on average by 2 users
Page 1/2
18Gbps 4K HDR AVX Extender with
eARC, Audio Breakout & PoE
EX-100-H2-EARC
Quickstart Guide
Copyright © 2021 WyreStorm Technologies | wyrestorm.com
EX-100-H2-EARC Quickstart Guide | 210524
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Basic Wiring Diagram
IMPORTANT! Installation Requirements
•Visit the product page to download the latest rmware, document
versions, additional documentation, and conîž’guration tools.
•Read through the section for important wiring Wiring and Connections
guidelines before creating or choosing premade cables.
•While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
In the Box
1x EX-100-H2-EARC Transmitter
1x EX-100-H2-EARC Receiver
1x 12V DC 3A Power Supply (US/UK/EU/AU)
1x IR Receiver
1x IR Emitter
4x Mounting Brackets with screws
2x 3-pin Terminal Blocks
1x QuickStart Guide (this document)
KEY
HDMI (eARC)
Control
Power
Ethernet/AVX
Digital Audio
Transmitter Receiver
LAN
Control System
AVR
Display Device
Copyright © 2021 WyreStorm Technologies | wyrestorm.com
EX-100-H2-EARC Quickstart Guide | 210524
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
2 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
RS-232 Wiring
The EX-100-H2-EARC uses a 3-pin RS-232 with no hardware flow control.
Most control systems and computers are DTE where pin 2 is RX, this can vary
from device to device. Refer to the documentation for the connected device for
pin functionally to ensure that the correct connections can be made.
Refer to for details on setting RS-232 modes.RS-232 Mode Settings
3rd Party Device
Pin 1 TX (Transmit) > To > RX (Receive)--- ---
Pin 2 RX (Receive) > To > TX (Transmit)--- ---
Pin 3 G (Gro d) > To > G (Gro d)un --- --- un
WyreStorm Co ectornn
IMPORTANT! Wiring Guidelines
•The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
•WyreStorm recommends the use of shielded category cable to minimize
signal noise and interference.
•WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
.
IR TX/RX Guidelines
•Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received by the system.
Other 3rd party emitters and receivers can be used; however, these devices
must operate in the same manner as the WyreStorm devices.
•Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within
the port. Refer to the product page for more information.CAB-IR-LINK
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: Anode
Sleeve: Cathode (IR Signal)
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
eARC/ARC LED
The EX-100-H2-EARC shares one LED to signify whether the extender is
transmitting an ARC or eARC signal. Based on the the LED transmission,
behavior changes as below.
Solid:
Solid:
Solid:
Solid: Solid: eARC audio is transmitting
Flashing:
Flashing:
Flashing:
Flashing: Flashing: ARC audio is transmitting
Product Specifications
| Brand: | WyreStorm |
| Category: | AV extender |
| Model: | EX-100-H2-EARC |
Do you need help?
If you need help with WyreStorm EX-100-H2-EARC, ask a question below and other users will answer you
AV extender WyreStorm User Manuals
14 October 2024
AV extender User Manuals
- AV extender StarTech.com
- AV extender Extron
- AV extender Lindy
- AV extender Smart-AVI
- AV extender Atlona
- AV extender Rocstor
- AV extender Genexis
- AV extender PureLink
- AV extender Kramer
- AV extender ATen
- AV extender Blustream
- AV extender C2G
- AV extender Intelix
- AV extender Comprehensive
Latest AV extender User Manuals
22 October 2024
22 October 2024
19 October 2024
19 October 2024
18 October 2024
18 October 2024
18 October 2024
18 October 2024
18 October 2024
18 October 2024