Blustream MFP62 Manual
Read below 📖 the manual in Italian for Blustream MFP62 (8 pages) in the Router category. This guide has been helpful for 36 people and has been rated 4.5 stars on average by 2 users
Page 1/8
MFP62
User Manual
RevA1 MFP62 User Manual
contact support@blustream.com.au | support@blustream.co.ukwww.blustream.com.au | www.blustream.co.uk
MFP62 USER MANUALMFP62 USER MANUAL
0302
Our MFP62 is an advanced 4K multi format presentation switch featuring 3 x HDMI,
1 x USB-C, 1 x DisplayPortâ„¢ and 1 x VGA input to dual HDMI outputs. The MFP62 provides
enhanced features including video scaling on outputs, MIC input with phantom power and
audio mixing. The MFP62 also features web GUI for control and configuration, analogue
audio embedding, audio de-embedding and control via front panel, IR, RS-232 and
TCP/IP. The MFP62 is an ideal product for your boardroom, classroom or huddle-space
application.
IntroductionContents
Surge protection device
recommended
This product contains sensitive
electrical components that may be
damaged by electrical spikes, surges,
electric shock, lightning strikes, etc.
Use of surge protection systems is
highly recommended in order to
protect and extend the life of your
equipment.
Thank you for purchasing
this product.
For optimum performance and safety,
please read these instructions carefully
before connecting, operating or
adjusting this product. Please keep this
manual for future reference.
Introduction 03
Features 03
Panel Descriptions 04
Microphone Input & Audio Mixing 05
EDID Control 06
Scaler Control 06
Infrared (IR) Distribution 07
Remote Control 08
RS-232 Control Port 09-10
Specification 11
Package Contents 11
Maintenance 11
Schematic 12
Installer Notes 13
• Features 3 x HDMI, 1 x USB-C, 1 x DisplayPort™ & 1 x VGA input which can be routed to dual HDMI outputs
• Supports HDMI 2.0 18Gbps specification including HDR
• Supports resolutions up to 4K UHD 60Hz 4:4:4
• Supports all known HDMI audio formats including Dolby TrueHD, Atmos and DTS-HD Master Audio transmission
• Dual HDMI outputs with simultaneous video scaling
• Supports USB Type C up to 4K UHD 60Hz 4:4:4, DP1.2 & Alt mode
• Supports DisplayPort™ up to 4K UHD 60Hz 4:4:4, DP1.2
• Audio breakout to analogue L/R audio and Coaxial (S/PDIF) digital outputs concurrently
• Features audio mixer with independent level adjustment
• Analogue audio embedding
• MIC input supports line level, 48V Phantom power or 1ch balanced / un-balanced audio
• Web interface module for control and configuration of switch
• Control via front panel, IR, RS-232 and TCP/IP
• HDCP 2.2 compliant with advanced EDID management
FEATURES:
contact support@blustream.com.au | support@blustream.co.ukwww.blustream.com.au | www.blustream.co.uk
MFP62 USER MANUALMFP62 USER MANUAL
0504
Panel Description - Front
Panel Description - Rear
1 LCD display – Shows the status of input/output selection,
EDID etc
2 Power button – Press to power on/o the Switcher.
Illuminates blue when powered on
3 Mutes all audio output
4 Input selection - To select the input signal between HDMI 1
to 3, DP, USB-C and VGA
5 Timing selection - To select scaler output video resolution
6 Menu button – Press to enter EDID, Network and MIC setup
menu
7 Up selection button – Press to change segment’s value
8 Enter button – Press to select current menu item.
9 IR receiver window
q L/R In button - Press to select analogue audio input to be
embedded onto all video signals
w Vol +/- button - Press to adjust the volume of the audio
output for 2ch PCM signals only
e Down selection button – Press to change segment’s value
r ESC button – Press to escape the current setup menu
1 TCP/IP (RJ45) – Connect to LAN for TCP/IP control of
Switcher and Web GUI
2 RS-232 port – For control of the Switcher from PC or third
party control processor
3 Coaxial digital audio output – Extract audio from the
selected input signal
4 L/R analogue audio outputs (RCA) – Extracted audio from
the selected input signal. Note: Input signal must be PCM
2ch audio
5 Upgrade port (Micro USB) - For firmware upgrade
6 SC/MB switch - For firmware upgrade of scaler or main
board
7 HDMI input 1 - Connect to HDMI source. Supports up to 4K
60Hz 4:4:4 video and 2ch PCM audio only
8 Status LED - Illuminates when an input or output has an
active connection to a source or display
9 HDMI input 2 to 3 - Connect to HDMI source. Supports up
to 4K 60Hz 4:4:4 video and multi channel audio
q DisplayPortâ„¢ input - Connect to DisplayPort source.
Supports up to 4K 60Hz 4:4:4 and DP1.2
w USB-C input - Connect to USB-C source. Note: this port
does not support charging via USB. Supports up to 4K
60Hz 4:4:4, DP1.2 and Alt mode
e VGA input - Connect to VGA source. Supports up
1920x1200 (including 1080p)
r L/R In - 3.5mm Analogue audio input for embedding audio
onto HDMI outputs
t HDMI outputs - Connects to HDMI display. Both outputs
display the same signal concurrently
y MIC IN - Supports balanced and unbalanced microphones
including 48V phantom power
u MIC input selection - Select between 48V phantom power,
line level and mic level input sensitivity
i IR selection - Select between 5V or 12V IR on the IR CTRL
connection. See full manual for pin out
o IR CTRL receiver input – 3.5mm stereo jack for connection
of an IR receiver or control processor for remote IR control
of the switcher
p Power port – Use included 24V/1A DC adaptor to power
the switcher
1
9
2 3 5
10 11 13
6 7 8
12
1
12
3 4
13 16 19
5 6
18
2
7 9 10 11
14
15 178
4
Microphone Input & Audio Mixing
The MFP62 features a microphone input that can support 48V phantom power, balanced and unbalanced microphones, as well
as line level audio input. It also features auto audio ducking where by the input source’s audio decreases in volume and the
microphone audio is mixed over the top. This feature is enabled by default and can be customised via the MFP62’s web GUI or RS-
232. The illustration below outlines how the microphone audio mixes over the input source’s audio.
When using the microphone mixing functionality, it is recommended to only use 2ch audio sources, or set the EDID of the product
to a 2ch EDID. While the MFP62 does support multichannel audio, mixing the microphone input over the multichannel signal is not
possible hence the source audio drops out when the microphone audio is triggered. To enable multichannel audio support, you
must choose a multichannel EDID via the Web GUI of the product.
All the microphone mixing features can be adjusted via RS-232.
The RS-232 commands assosciated with each item are as follows:
Product Specifications
| Brand: | Blustream |
| Category: | Router |
| Model: | MFP62 |
Do you need help?
If you need help with Blustream MFP62, ask a question below and other users will answer you
Router Blustream User Manuals
19 October 2024
18 October 2024
18 October 2024
18 October 2024
18 October 2024
18 October 2024
Router User Manuals
- Router Xiaomi
- Router Bosch
- Router Huawei
- Router HP
- Router Lancom
- Router TP Link
- Router D-Link
- Router StarTech.com
- Router Kogan
- Router Asus
- Router Cudy
- Router Netgear
- Router Hikvision
- Router Mikrotik
- Router Keezel
- Router Silentwind
- Router Alcatel
- Router Ubiquiti Networks
- Router SPL
- Router A-NeuVideo
- Router Atlona
- Router Luxul
- Router Teltonika
- Router MuxLab
- Router Starlink
- Router Kramer
- Router ATen
- Router Milesight
- Router Arris
- Router Tenda
- Router Draytek
- Router WyreStorm
- Router KanexPro
- Router Alfatron
- Router Digitalinx
- Router Intelix
- Router Comprehensive
- Router Ocean Matrix
- Router Sabrent
- Router Predator
- Router FSR
- Router PulseAudio
- Router Alfa
- Router Amped Wireless
- Router Keewifi
- Router Keenetic
Latest Router User Manuals
27 October 2024
26 October 2024
24 October 2024
24 October 2024
20 October 2024
19 October 2024
18 October 2024
18 October 2024
17 October 2024
17 October 2024