Enda ET2011 Manual
Enda
Thermostat
ET2011
Read below 📖 the manual in Italian for Enda ET2011 (4 pages) in the Thermostat category. This guide has been helpful for 30 people and has been rated 4.5 stars on average by 2 users
Page 1/4
230V AC +%10 -%20, 50/60Hz 24V AC %10, 50/60Hzor
Max. 5VA
Power : , Si : 1 ²connector 2.5mm²' screw-terminal gnal connector ,5mm screw-terminal conenction.
EEPROM ( )minimum 10 years
Max. 100ohm
1 bit2
00ms1
R : 250V AC, 8A (for resistive load), Selectable as NO+NC Control or Alarm2 output.elay
°C
Withot load 30.000.000 mechanical operation; 250V AC, on the 8A resistive load 100.000
electrical switching
C/A2 output
ENDA ET2011 PID TEMPERATURE CONTROLLER
* x mm .77 35 sized
Thank you for choosing 2011 temperature controller.ENDA ET
TECHNICAL SPECIFICATIONS
* Selectable dual-set value.
* Se tlectable thermocouple ypes or Pt100 input.(Selection must be
* Soft-Start feature.
* (SELF TUNE).Automatic calculation of PID parameters.
* Selectable heating/cooling control.
* C/A2 Relay output can be programmable as alarm or control output.
* .Selectable SSR control output
* Input offset feature.
* In the case of sensor failure periodical running or relay state can be
selected.
Input type
Temperature range
J (Fe-CuNi) Thermocouple
K (NiCr-Ni) Thermocouple
T (Cu-CuNi) Thermocouple
S (Pt 0Rh-Pt) T1 hermocouple
R (Pt13Rh-Pt) Thermocouple
EN 60584
EN 60584
EN 60584
EN 60584
EN 60584
0... 600
0...1300
0... 400
0...1700
0...1700
°C
°C
°C
°C
°C
Accuracy
0, % ( )5 of full scale
0, % ( )5 of full scale
1 digit
1 digit
0, % ( )5 of full scale 1 digit
0, % ( )5 of full scale 1 digit
0, % ( )5 of full scale 1 digit
+32... +1112
+32... +2 237
+32... +752
+32... +3092
+32... +3092
°F
°F
°F
°F
°F
°C
°F
SSR output
Max 20mA 12Volt (as control output)
SET
°C
SET
ET2011
ENDA
°F
C/A2
SSR
F
Pt 100 Resistance thermometer
Pt 100 Resistance thermometer
EN 60751
EN 60751 -200...600 °C
-328...1112 °F
- ... 00 °C99.9 3 .0
- ...543 °F99.9 .0
0,5% (of full scale)
1 digit
0,5% (of full scale) 1 digit
specified in order).
Enter PID parameters of the system if they are known at the beginning.
Otherwise, Self-Tune should be activated.
ENVIRONMENTAL CONDITIONS
Height
Max. 2000m
80 up to 31 decreasing linearly 50 at 40.% %
Ambient/storage temperature
Max. Relative humidity
0 ... +50 /°C -25... +70°C (with no icing)
Rated pollution degree
According to EN 60529 Front panel : IP65
Rear panel : IP20
Do not use the device in locations subject to corrosive and flammable gases.
OUTPUTS
Life expectancy for relay
ELECTRICAL CHARACTERISTICS
Supply
Power consumption
Wiring
Line resistance
Data retention
EMC
Safety requirements
EN 61326-1: 2006
EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)
CONTROL
Control type
Single set-point and alarm control
Control algorithm
A/D converter
Sampling time
Proportional band
Control period
Hysteresis
Output power
Adjustable between 0 and 100 . If Pb=0 , On-Off control is selected.% % %
and 250 secondsAdjustable between 1
1 and 50Adjustable between °C/F
The ratio of power at a set point can be adjusted between 0 and 100% %
HOUSING
Housing type
Suitable for flush-panel mounting according to DIN 43 700.
Dimensions
W77xH35xD71mm
Weight
Approx. 200g (after packing)
Self extinguishing plastics.
Enclosure material
While cleaning the device, solvents (thinner, benzine, acid etc.) or must not be used.corrosive materials
Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.
R : 250V AC, 16A (for resistive load), Selectable as NO Control or Alarm2 output.elay
english
1. / 4
E-mail : info@suran-elektronik.de
Internet : www.suran-elektronik.de
Tel.: +49 (0)7451 / 625 617
Fax: +49 (0)7451 / 625 0650
SURAN Industrieelektronik
Dettinger Str. 9 / D-72160 Horb a.N
ET2011-E-06052019
SET
SET
C.s.lo.= Control set point lower limit.(for
selected output)
Adjustable between 0 and C.s.Hi.
C.s.Hi.= Control setpoint upper limit.(for
selected output)
Adjustable between and Upper scale
value.
C.s.Lo.
a2.s.l= Alarm2 set value lower limit.
Adjustable between 0 and A2.S.H
parameter value.
a2.s.H= Alarm2 set value upper limit.
Adjustable between
parameter value and upper scale
value.
A2.S.L
a2.Hy=
.
Hysteresis of the Alarm2
output
Adjustable between 1 and 50 °C.
A2.st.
Hi
= The state of Alarm2 output.
If A2 output is above the set
value. (on)
=
lo= If A2 output is above the set
value.(off)
A2.Er.
on
=
2 output is probe failure (on).
State of Alarm2 output in the
case of sensor failure.
= A
off= A2 output is probe faiure (off).
A2.tp
indE.
dE.
bAnd
bAn.i
= Function of Alarm type.
Four kinds of functions can be
selected.
= alarm
(Independent)
= Deviation
= Band alarm (Band)
= Band with inhibition
2
Independdnt
inp.t.
FE.cn. nc.nA. c.cn.
p10.r. P13.r.
=
= J type , = K type = T
type =S type , = R type
thermocouple selection.
This parameter varies when changing
some parameters.
Input type selection.
Unit = The temperature unit.
°C °F= °C, = °F
(This parameter varies when
changing some parameters.)
C.o.sE = Control output selection
C-A2
SSR
= C/A2 (Relay) output selection
= SSR output selection
F.kE.C. = Function key setting parameter
nonE
C2.S.A.
manu.
dSP.o
= Function key is off.
= The function key with 2.set value is used.
= Manual mode can be achieved with the function key.
= Device only the temperature display mode is entered
with function key.
.
C. Pb
C. Pb
=
%0 %100
= %0 On-Off
Proportional band.(for selected
output)
Adjustable between .0 and .0.
.0, control is selected.
C. ti
C. ti
C. Pb
=
=
Integral time.(for selected output)
Adjustable between 0 and 100.0 minutes.
0.0,integral impact is disable.
parameter is different from “0”,this
parameter appears.
C.Hys
C. Pb
= Hysteresis of the output.(for
selected output)
Adjustable between 1 and 50 °C.
= 0,this parameter is active.
C. td
C. td
C. Pb
=
=
Derivative time.(for selected output)
Asjustable between 0.00 and 25.00 minutes.
0.0, derivative time is disable.
parameter is different from”0”,this
parameter appears.
C. Ct.
C. Pb
= Period time.(for selected output)
Adjustable between 1 and 250 second.
parameter is different is different
from“0”,this parameter appears.
C.p.st = The ratio of output power at the
setpoint.Adjustable between %0 and %100.
C.E.P.s. = The percentage of faulty sensor
selected output power.Adjustable between
%0 and %100.
C.typ. = Control output type
C.typ. HEAt
C.typ. CooL
=
=
means heatign control.
means cooling control.
While the parameter names appear,if and
keys are pressed together, returns to the program
mode.
S.Cod =
.
Security menu access
code
It should be 2011.
Cosc. CoN.o.
nonE
P.yEs
P. no
=
=
=
Parameters of
menu security access level code.
Invisible.
Modification can be done.
= Only visible.
m.SEt.
C. Pb.
=
This parameter allows manual adjustment of the output
power when the manual output selection.
, this parameter is not seen.
The percentage of manual output parameter.
Adjustable between %0 and %100.
0=
this parameter is seen and
adjustable only
if set co.SE SSR =
a.2.sc. al2.o.
nonE
P.yEs
P. no
=
=
=
Parameters of
menu security access level code.
Invisible.
Modification can be done.
= Only visible.
Co.sc. Conf.
nonE
P.yEs
P. no
=
=
=
Parameters of
menu security access level code.
Invisible.
Modification can be done.
= Only visible.
S.t.Sc. S.tun.
nonE
P.yEs
=
men
=
=
Parameters of
u security access level code.
Invisible.
Modification can be done.
Co.sc. Conf.
no
yEs
=
m
=
=
Parameters of
enu security access level code.
Parameter settings are not
change.
Parameter setting will be
restored.
C.s.Lo.
C.s.Hi.
C. pb
C. ti
C. td
C.p.st
C.Hys
C. Ct.
C.typ
s.s.t.s.
C.E.p.s.
Con.o.
AL2.o.
ConF.
S.tun.
SEcu.
S.Cod.
Co.sc.
m.SEt.
a.2.sc.
Cn.sc.
S.t.sc.
dEF.P.
inp.t.
Unit
fltr.
C.o.sE
offs.
s.t.Co.
F.k.E.C.
A2.S.L
A2.S.H
A2.HY
A2.tP
A2.St.
A2.Er.
SET
SET
SET
SET
SET
F
Programming mode
This parameter indicates the time to reach set point
value when the device is first enegised.
Adjustable between 0 and 250 minutes.
If 0 is selected, soft start feature will be enable and the
device reaches set point value quickly.
Pb = 0, so start feature will be disable. Setting ft
Sst.S =Sofy starter timer set value
fLtr.= Coefficient of digital filter.
Filter for display value.
Adjustable between 1 and . If this parameter is 1,
digital filter runs most quick. If the parameter is ,
the filter run most slow. The value of parameter should
be increased in interference.
200
200
oFfS. = Offset value.
Offset value is added to the measurement value.
Adjusted between -100 and +100°C.The normal value is 0.
St.Cu = Self tune control parameter.
If both keys are pressed ,
message is displayed on the screen
and self tune process is started
automatically.
If both keys are pressed,
message is displayed on the screen
and self tune process is stopped.
yes
no
Selt tune begins when the measurement,
and measurement value
are shown alternately.Self tune process
completed automatically after the
parameter is done no and is entered to the
working mode. Self tune process begin when
the measured temperature is expected fall
below 90% of the set value the display shows
message alternately.Expected to fall
below the temperature set point 60% evolved
and then self tune process starts automatically.
If asked to abort the self tune process,
parameter is done and key is
pressed.
PIdt.
stco
te.HI
St.Co
no
message
SET
If key is pressed while holding key, the programming mode is enabled.
SET
F
Entering from the programming mode to the run mode:
If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered.
Alternatively, the same function occurs first pressing key and key is pressing programming mode is entered.Then and keys are pressing
together,data is recorded and running mode is entered.
Modification Of Parameter Diagram
When holding key, the value of parameter flashes and using
keys the requested value can be adjusted.
If key is pressed and held 0.6 seconds, the value of the selected
parameter changes rapidly. If waited enough,the value increases 100 at each
step. After 1 second following the release of the key, initial condition is
returned.The same procedure is valid for the decrement key.
SET
SET SET
SET
C.s.lO.
inp.t.
A2.s.l
Co.sc.
C1.sE.
C.s.Hi.
Unit
A2.s.H
A2.Sc.
C2.SE.
C. PB
Fltr.
A2Hy.
Cn.Sc.
A2.SE.
C.HyS
C.o.SE.
A2.tp
S.t.Sc.
C. ti
offs.
a2.st.
dEf.P.
C. td
f.k.E.C.
a2.Er.
a2.Er.
C. Ct.
m.sEt.
C.P.St.
C.EP.S.
S.s.t.S.
C.typ.
TC input
TC input
TC input
TC input
TC input
Pt100 input
Pt100 input
Pt100 input
Pt100 input
Pt100 input
0
FE.cn.
0
0
25
2
2
C-A2
indE
P.yEs
P.yEs
400
P.yEs
400
P.yEs
500
4.0
0
Hi
no
1.00
nonE
on
no
20
50
0
0
0
HEat
-200
Pt.
-200
600
°C
600
DEFAULT PARAMETERS
Set parameters
Control output
parameters
Alarm2 output
parameters
Configuration
parameters
Self tune
parameters
Security
parameters
SET
SET
2. / 4
ET -E-050620192011
NOTE:
If the output does not switch the relay and the C / A2 LED
does not light up though correct wiring and parameter
settings of the device:
Parameter on change over with the "F" key
from temperature indicator to temperature controller, then
change parameters back to “ ".
or
Reset the device to factory settings.
FtEC dSP.o
nonE
.
SET
°C
SET
ET2011
ENDA
°F
C/A2
SSR
F
TERMS
mm12
( 1 ) )
Paramet (Progra )
Measurement value and set value indicator Running mode
er name and value mming mode
( ) ( rogram )
If only this key is pressed in normal operation,software version
number is seen. parameter processing
2 Value increment key P ming mode
(F.k.E.C. )
( )
( rogram )
2 Value decrement and parameter selection key.
P ming mode
( ) ( )
Paramet (Program )
4 Control ve Alarm set selection key Running mode
er set key ming mode
7 4 LED display segment, digits red
Mikro switch
, Alarm1 SSRFor control and outputs 3 digits red LED
MODIFICATION OF CONTROL AND ALARM SET POINTS
ERROR MESSAGES
Character heights
( ),( ),( )2 3 4 Keypad
( )5 State indicator
ALARM2 OUTPUT TYPES
Independent Alarm
A2.tp. indE=
=
Deviation Alarm
A2.tp dE.
Band
=
Alarm
A2.tp. bAnd
=
Band Alarm With Inhibition
A2.tp. bAn.i
A2.St. Hi=
A2.St. lo=
=A1.St. Lo
=A2.St. Hi
ASV
SV
SV
SV
SV+ASV
SV+ASV
SV-ASV
OFF
OFF
OFF
OFF
OFF
OFF
-300
300
+300
300
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
Beginning
SV = ASV = (ASV min. = 0, ASV maks. = 300 )Set point of CONT output Set point of AL2 output
SV = ASV =Set point of CONT output Set point of alarm output
(ASV min. =-300, ASV ma . = +300)x
(ASV min. = 0, ASV ma = +300)X.
(ASV min. =
ASV ma = )
beginning of scale
x. end of scale
SV = ASV =Set point of CONT output Set point of AL2 output
Band alarm is possible
Band alarm is possible
Beginning
SV
SV
SV+ASV
SV+ASV
SV-ASV
SV-ASV
a2,Hy
A2.Hy
A2.Hy
A2.Hy
SET
( 1 ) PV and SV display
( )5
3 seconds later
3 seconds later
3 seconds later
3 seconds later
250
pfa
psC
____
C1.SE.
C2.SE.
a2.SE.
400
398
500
399
399
499
SET
C.O.SE.parameter is set to the output of SSR,this
parameter is seen.
Sensor is broken
Pt100 sensor is short circuit
Temperature value is
higher than the value
Temperature value is
lower than the scale
parameter, is set to the parameter,this
parameter is displayed.
F.kE.C. C2.S.A.
----
3. / 4
E-mail : info@suran-elektronik.de
Internet : www.suran-elektronik.de
Tel.: +49 (0)7451 / 625 617
Fax: +49 (0)7451 / 625 0650
SURAN Industrieelektronik
Dettinger Str. 9 / D-72160 Horb a.N
ET2011-E-06052019
Product Specifications
| Brand: | Enda |
| Category: | Thermostat |
| Model: | ET2011 |
Do you need help?
If you need help with Enda ET2011, ask a question below and other users will answer you
Thermostat Enda User Manuals
16 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
15 October 2024
Thermostat User Manuals
- Thermostat ATAG
- Thermostat Bosch
- Thermostat AEG
- Thermostat Siemens
- Thermostat EBERLE
- Thermostat Schwaiger
- Thermostat Oreg
- Thermostat Netatmo
- Thermostat Busch-Jaeger
- Thermostat Danfoss
- Thermostat Schneider
- Thermostat EMOS
- Thermostat Heatit
- Thermostat Dimplex
- Thermostat Velleman
- Thermostat GE
- Thermostat Tru Components
- Thermostat Bearware
- Thermostat Max
- Thermostat Elgato
- Thermostat EVE
- Thermostat ORNO
- Thermostat Avidsen
- Thermostat STI
- Thermostat Hunter
- Thermostat Basetech
- Thermostat TFA
- Thermostat REMKO
- Thermostat Vaillant
- Thermostat Boneco
- Thermostat Grohe
- Thermostat Drayton
- Thermostat Jung
- Thermostat Ambiano
- Thermostat Crestron
- Thermostat Xavax
- Thermostat Remeha
- Thermostat Heatmiser
- Thermostat Hive
- Thermostat GENERAL Life
- Thermostat Silvercrest
- Thermostat HomePilot
- Thermostat Elektrobock
- Thermostat Corberó
- Thermostat Delta Dore
- Thermostat Homematic IP
- Thermostat Vimar
- Thermostat Emerson
- Thermostat Salus
- Thermostat Fenix
- Thermostat Baxi
- Thermostat Honeywell
- Thermostat Google
- Thermostat Emko
- Thermostat Wachendorff
- Thermostat Elro
- Thermostat De Dietrich
- Thermostat Theben
- Thermostat Computherm
- Thermostat Vemer
- Thermostat Grasslin
- Thermostat Niko
- Thermostat H-Tronic
- Thermostat Gira
- Thermostat Fantini Cosmi
- Thermostat Radson
- Thermostat Junkers
- Thermostat Buderus
- Thermostat Viessmann
- Thermostat Tado
- Thermostat Amfra
- Thermostat Aube
- Thermostat Eneco
- Thermostat Orbis
- Thermostat Emmeti
- Thermostat Optima
- Thermostat Drayton Erie
- Thermostat Carrier
- Thermostat Eurotronic
- Thermostat PECO
- Thermostat Intertechno
- Thermostat Maico
- Thermostat Frico
- Thermostat Bulex
- Thermostat Gewiss
- Thermostat Etherma
- Thermostat Horstmann
- Thermostat Plugwise
- Thermostat Mikoterm
- Thermostat Cepra
- Thermostat ChiliTec
- Thermostat King
- Thermostat Sygonix
- Thermostat Landis Gyr
- Thermostat Saunier Duval
- Thermostat Itho-Daalderop
- Thermostat Finder
- Thermostat ICY
- Thermostat THERMAFLEX
- Thermostat Rose LM
- Thermostat Seitron
- Thermostat IMIT
- Thermostat Watts
- Thermostat Nefit
- Thermostat Econo-Heat
- Thermostat EQ3
- Thermostat Ferroli
- Thermostat Hager
- Thermostat Otio
- Thermostat Jumo
- Thermostat EQ-3
- Thermostat Magnum
- Thermostat Webasto
- Thermostat UPM
- Thermostat Eqiva
- Thermostat Johnson Control
- Thermostat Devi
- Thermostat Tylö
- Thermostat AWB
- Thermostat ELKO
- Thermostat Yokis
- Thermostat Technoline
- Thermostat 2Heat
- Thermostat RWE
- Thermostat ACV
- Thermostat Plieger
- Thermostat Veria
- Thermostat Wallair
- Thermostat Stiebel Eltron
- Thermostat Trotec
- Thermostat Hugo Muller
- Thermostat VDH
- Thermostat Ouellet
- Thermostat Nest
- Thermostat Innogy
- Thermostat Devolo
- Thermostat Zehnder
- Thermostat Go Green
- Thermostat EasyTemp
- Thermostat Levica
- Thermostat Coati
- Thermostat Berker
- Thermostat MundoControl
Latest Thermostat User Manuals
25 October 2024
25 October 2024
25 October 2024
25 October 2024
25 October 2024
25 October 2024
25 October 2024
25 October 2024
25 October 2024
25 October 2024